User manual MTD CUBCADET 5000

[. . . ] 769-02933 18( 4VSHYGXW %OXMIRKIWIPPWGLEJX w 7EEVFV²GOIR w +IVQER] 1 Y X A 2 B C W V U T E S I R Q K P L L M H G F I J 3 FUEL E F HOURS 1/10 RPM 0 x1000 4 D 4 5 O N 6 (b) (c) (a) 7 L N H 8 (a) (b) (d) 9 10 (b) (a) 11 1 2 3 7 4 8 10 9 12a HOURS 1/10 FUEL RPM E F 0 x1000 4 5 6 2 1 12b 3 13 b a 14 15 b 16 a b MAX MIN a 17 b 18 b a 19 c b a a 20 b a 21 22 b b c a a b 23 8 10 17 9 15 5 19 18 4 16 2 11 10 7 15 6 12 20 5 3 6 15 13 14 24 a c 25 b English Français Deutsch Nederlands Svenska Dansk Español 4 21 41 59 78 94 112 English Operating Instructions This unit is not intended for purposes beyond those listed above. The user is liable for all damage to third parties and their property. As standard, in its standard configuration, this vehicle is not approved for operation on public roads or for transporting people. Only operate the appliance in the technical condition stipulated and supplied by the manufacturer. [. . . ] n Hold the belt and pull the latch to the left in order to remove the slack in the upper lying belt between the readjustment and the latch. n To shorten the belt, tip the other side of the clip upwards, pull the free end of the belt to the right and pull the latch to the left in order to remove the slack. Check the tyre pressure Note For manufacturing reasons, the tyre pressure can be higher than necessary. Correct where necessary (see section "Servicing"). ­ front 1. 0 bar ­ rear 0. 7 bar Stopping the engine n Starting the engine n n Sit in the driver seat. Set the gear lever to the neutral setting N. n Push the brake pedal down fully or lock the parking brake. Diesel motors have to be preheated before starting the engine. Reaching the required temperature for starting the engine is indicated by the glow plug pilot light going out. n n n Cool the engine down appropriate to the previous workload. ­ In the case of less of a workload. Set the throttle to the position and let the engine run for approx. ­ In the case of a high workload: set the throttle to the middle setting and let the engine run for 3­5 minutes. Lock the parking brake. Driving the tractor !;EVRMRK %FVYTX XEOISJJ WXSTTMRK WYHHIRP] ERH HVMZMRK EX I\GIWWMZI WTIIHW VEMWI XLI VMWO SJ EGGMHIRXW ERH GER GEYWI HEQEKI XS XLI YRMX 11 English &I IWTIGMEPP] GEYXMSYW [LIR VIZIVWMRK 2IZIV GLERKI XLI HMVIGXMSR SJ XVEZIP SV XLI WTIIH [MXLSYX JMVWX FVMRKMRK XLI ZILMGPI XS E WXERH 2IZIV WIXEHNYWX XLI HVMZIV W WIEX [LMPI XLI YRMX MW QSZMRK n Set the driver seat. n Raise the attachments which are mounted to the 3 point attachment device. n Press the brake pedal down fully and release the parking brake. n Set the drive lever to the desired speed (high/low). n Set the drive lever to the optimum range for the job (as a rule, maximum). n Release the brake pedal and at the same time, slowly actuate the accelerator and/or reverse pedal until the desired speed is achieved. Before starting the journey, make sure that the front wheels are in the desired direction. Note The lower drive lever speed setting should ­ be used to travel on slopes and uneven ground, ­ when using attachments on the PTO. Operating Instructions Switching the differential lock on and off ;EVRMRK 6MWO SJ ER EGGMHIRX SGGYVVMRK ERH HEQEKI XS XLI ZILMGPI r 3RP] W[MXGL XLI HMJJIVIRXMEP PSGO SR [LIR XLI ZILMGPI MW EX E WXERH r (S RSX EGXYEXI XLI HMJJIVIRXMEP PSGO [LIR HVMZMRK SR XLI VSEH LEVHIRIH WYVJEGI ERH EX WTIIH WXIIVMRK HMJJMGYPXMIW r VMWO SJ ER EGGMHIRX n n n Bring the vehicle to a stand Depress the differential lock fully and keep it depressed. The differential lock is activated (even transfer of power onto both rear wheels). The differential lock is switched off. Note Releasing the differential lock pedal does not always disengage the differential lock. [. . . ] The starting torque for the screws / nuts is 81 ­ 94 Nm. Troubleshooting !;EVRMRK 6MWO SJ MRNYV] XLVSYKL XLI IRKMRI FIMRK YRMRXIRXMSREPP] WXEVXIH 4VSXIGX ]SYVWIPJ JVSQ MRNYV] &IJSVI HSMRK ER] [SVO XS XLMW ETTPMERGI r XYVR XLI IRKMRI SJJ r VIQSZI XLI MKRMXMSR OI] r PSGO XLI TEVOMRK FVEOI r ;EMX YRXMP EPP QSZMRK TEVXW LEZI GSQI XS VIWX ERH XLI IRKMRI LEW JYPP] GSSPIH Faults when operating your appliance often have simple causes which you should know about and which you can partly deal with yourself. In case of doubt, your specialist garage will be happy to help you further. Charging the battery Check the battery's charged state with a voltmeter. When the charged state is less than 12. 6 V (DC) recharge the battery (max 12 V at 10 A) with a battery charger in accordance with the table. [. . . ]