User manual MTD EAGER BEAVER 282HD

[. . . ] Trigger gun safety lock Trigger gun Pull start (not seen) Gas tank Throttle (not seen) Choke (not seen) Wand w/adjustable spray nozzle High pressure outlet Engine Air Cleaner Pressure Control 10. 0 HP Kohler Command 3. 0 GPM 3000 PSI 5 4 3 8 9 7 13 14 10 11 12 15 2 18 17 16 1 6 SAFE OPERATION PRACTICES — NEVER! Never point nozzle at people or animals. Never drink alcohol or use drugs while operating this equipment. Never spray electrical connections, electrical outlets or fixtures. Never add fuel with the engine running or operate where fuel has been spilled. [. . . ] Low pressure detergent application “CHEM” position The low pressure chemical setting is used for the application of approved detergents. Rotating Spray Nozzle This nozzle features a 0° pencil jet which rotates 360° for maximum dirt cutting action, effectively increasing cleaning performance up to 50%. This nozzle combines the cleaning performance of a 0° pencil jet with the surface coverage of a wide angle nozzle. Not recommended for soft materials, siding, painted surfaces, decks or autos. WARNING: TO AVOID SERIOUS INJURY, NEVER POINT SPRAY NOZZLE AT YOURSELF, OTHER PERSONS OR ANIMALS 9 CHEM WORKING WITH DETERGENT Detergents can only be applied in the “low” setting. CHE M Suction Tube Step1 To apply deter- Step2 Connect the sucgents the touch-less nozzle tion tube to the fitting on the Step3 Slide the detergent tray into the frame slot. must be set to the low pres- pump Secure the tray to the frame sure “CHEM” position. by fastening the screw. Step4 Fill a container with Cub Cadet detergent and place the container in the detergent tray. Place the filter end of detergent suction tube into the container. Be sure to adjust the filter by turning it to the desired detergent intake. For best results see Cleaning Tips on pages 12 & 13 for specific information on how to clean different surfaces. Always Use Cub Cadet Detergents for Best Results. Cub Cadet biodegradable detergents are specially formulated to protect the environment and your pressure washer. The special formulas will not clog the suction tube filter and will protect the internal parts of the pressure washer for a longer life. For Cub Cadet Detergents, check your local Cub Cadet dealer. If you need help locating a dealer in your area, contact the Customer Dealer Referral Line by calling: 1-877-835-7841 Step5 With the engine running, pull trigger to operate unit: Liquid detergent is drawn into the unit and mixed with water. If using Cub Cadet All Purpose Cleaner, place detergent suction tube directly into cleaning solution and apply to surface at low pressure. For best results, limit your work area to smaller sections of approximately 25 square feet. Allow Cub Cadet All Purpose Cleaner to remain on surface 1-3 minutes. Do not allow detergent to dry on surface. Allow Cub Cadet detergent to remain on surface 1-3 minutes. Do not allow detergent to dry on surface. Rinse at high pressure keeping the spray nozzle approximately 6 inches from the cleaning surface. For removing extremely stubborn dirt, it may be necessary to move the spray nozzle even closer to the surface for greater dirt cutting action. To remove caked on mud from garbage cans, lawn mower blades, wheel barrels or other non-sensitive metal surfaces, you may want to use the Cub Cadet Rotating Nozzle Spray Wand. Caution: Do not use rotating nozzle spray wand on cloth, plastic or other sensitive surfaces as it may cause damage. Patio & Lawn Furniture (with or without detergent) Pre-rinse furniture and surrounding area with fresh water. If using Cub Cadet All Purpose Cleaner, place detergent suction tube directly into cleaning solution and apply to surface at low pressure. [. . . ] Remove obstruction or replace detergent suction tube. Turn spray nozzle tip to low pressure position. Blow out or remove debris with a fine needle. Check that hoses and fittings are air tight. [. . . ]