User manual MTD OEM-290-266

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MTD OEM-290-266. We hope that this MTD OEM-290-266 user guide will be useful to you.

Lastmanuals help download the user guide MTD OEM-290-266.


Mode d'emploi MTD OEM-290-266
Download
Manual abstract: user guide MTD OEM-290-266

Detailed instructions for use are in the User's Guide.

[. . . ] Before installation, they should be filled as described below. Use a screwdriver to gently pry off the fill cap located in the center of each wheel weight shell, see Figure 1. Do not remove the post in the center of the cap as it is used for anchoring the cap to concrete or similar hard-drying fill material. [. . . ] GW-2382 1186411 GW-9904 736-0169 1186531 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . Wheel weight shell . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Bolt, Hex Hd. , 3/8" 16 x 6" . . . . . . . . . . . . . . . 4 Flat washer, 3/8" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Lockwasher, 3/8" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Hex nut, 3/8" -16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Tools and Materials Required: Fill material for weight shells; (See Step 2) Flat-blade screwdriver Scissors* Masking tape* Center punch* Hammer* Electric power drill with 1/4" and 7/16" or (1/4" and 3/8") high-speed drill bits. * Two 9/16" wrenches *NOTE: For 11 HP “Big Red” model the wheels are pre-drilled. These items are not needed. POST Fig. 1 Drill Mounting Holes To mount the wheel weights, two 7/16 inch holes need to be drilled in each wheel. This drilling can be done without removing the wheels from the tiller. Carefully cut the template (see attached sheet) along the inside and outside dotted lines. CAUTION Read instructions provided with the power drill before using. Place the template in the center of the wheel well, making sure that the arrow on the template is aligned with the air valve stem, as shown in Figure 2. Secure the template to the wheel with several strips of masking tape. Using a center punch and hammer, punch two drill guide marks exactly through the center of each (+) sign on the template. [. . . ] Repeat with the 7/16 inch drill bit, or use a 3/8 inch drill bit and ream the edges of the hole to 7/16 inch. At all times, keep the drill centered to ensure that the correct distance between the mounting holes is maintained. Repeat steps 2 through 4 for the second wheel. 1 2 3 4 5 Fig. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MTD OEM-290-266

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MTD OEM-290-266 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag