User manual MURATEC M-1100

[. . . ] To lock the scanner, please use the reverse process of the instructions below. 1 Slide the scanner locking knob to the back until it clicks in the unlocking position. 2 Turn off the transport mode (see Step 8 "Turn off the transport mode, " page 12). 4 Installation Manual Step 4 : Install the consumables 1 Pull the release lever to open the side cover. 2 Open the front cover. 3 Turn the toner cartridge locking lever to the left (unlock position). 4 Unpack the drum cartridge from its carton and slide it into the machine firmly until it locks into place. NOTE: DO NOT touch the drum surface. Installation Manual 5 5 Unpack the starter toner cartridge, hold it with both hands and gently shake it to distribute the toner evenly inside the cartridge. NOTE: Do not touch the roller of the toner cartridge. 6 Slide the toner cartridge into the machine firmly until it locks into place. Then turn the cartridge locking lever to the right until it locks into place. 7 Close the front and side covers. 6 Installation Manual Step 5 : Load paper into the cassette Acceptable paper sizes for the cassette: Region U. S. European and Asian countries Paper size Letter, Legal, Half-letter A4, A5 , F4 Paper type Plain paper Quantity 500 sheets (Weight: 20­24 lbs. 60­90g/m2) 60g/m2) 1 Pull the handle toward you to open the paper cassette. 2 Press the paper lifting plate down until it locks into position. 3 Adjust the rear paper guide to the desired paper length. Installation Manual 7 4 Load the paper into the cassette. [. . . ] · Make sure you properly stack the paper prior to setting it in the cassette. The leading edge and sides should be even. · Do not stack the paper over the limit mark inside the cassette. 5 Pinch the side paper guide and adjust it to the width of the paper. 6 7 8 9 Close the paper cassette. Attach the appropriate paper size sticker to the front of the cassette. If the optional second cassette has been installed, please follow these steps. See "Set the paper size" on page 15. 8 Installation Manual Step 6 : Connect the cables Connect the telephone line cable 1 Loop the telephone line cable and attach the ferrite core as shown. The telephone line cable loop should be near the connector of the cable. 2 Plug the telephone line cable into the LINE jack. PHO NE1 PHO NE2 LIN E 3 Plug the other end of the telephone line cable to the telephone wall jack. Connect the LAN cable NOTE: · A LAN cable is not supplied with the machine. · If you are not installing the machine on a network, please skip to "Connect the power cord". 1 2 Prepare a 10BASE-T or 100BASE-Tx LAN cable (Category 5). Loop the LAN cable and attach the ferrite core as shown. The LAN cable loop should be near the connector of the cable. Installation Manual 9 3 Plug the LAN cable into the LAN connector. PHONE1 PHONE2 LINE 4 Plug the other end of the LAN cable into a 10Base-T/100Base-Tx Ethernet hub, or into the appropriate RJ-45 wall jack. Ethernet hub Connect the power cord 1 Plug the non-pronged end of the supplied AC power cord into the AC socket on the machine. PHONE1 PHONE2 LINE 2 Plug the pronged end into a properly grounded AC outlet. NOTE : The appearance of the plug and outlet differs according to the countries. 10 Installation Manual Step 7 : Turn the power on 1 Turn the power on. The markings are international standards: [ | ] means on, [ ] means off. 2 3 If you are installing MFX-2030 or MFX-1430, perform Step 8 "Turn off the transport mode" first (see next page). Once the transport mode has been turned off, you may procedure to the next procedure. by pressing [Setting] [List] [Network Settings] [Yes] on the control panel. Go to "Verifying the IP settings" on page 19 and begin with step 2. NOTE: Once the DHCP server has assigned the IP address to your machine, that IP address MUST be reserved within the specific DHCP scope. Failure to do so could result in failed operation when the IP address lease expires. If your network is not using DHCP You should turn off the DHCP server setting. Then enter the IP address manually to install your machine on your network. 1 Press [Setting] on the control panel, then [Management]. 2 Press [Network Settings]. 16 Installation Manual 3 Press [TCP/IP Settings]. 4 Press [DHCP Setting]. 5 Select [OFF] and press [Enter]. NOTE: If you are not installing the machine on a network, please skip to step 14 "Local print and scan driver installation" on page 23. Installation Manual 17 6 Press [IP Address]. 7 Enter the appropriate IP address using the numeric keys. Press the arrow keys to navigate the field. Press [Clear] to delete a number. 8 9 Press [Enter]. The display returns to the TCP/IP settings menu. Press [Subnet Mask] and enter the appropriate IP address, then press [Enter]. Refer to the above steps on how to enter the IP address. 10 If necessary, enter the gateway address. 11 When you are finished, reboot the machine to activate the new settings. (Turn the machine off and after three or more seconds, turn it on. ) 12 Go to "Verifying the IP settings" on next page. 18 Installation Manual Verifying the IP settings 1 2 Print the network setting list to view the new configuration. To print the network settings list: Press [Settings], [List], [Network Settings], then [Yes] At the command prompt on a network computer, type "ping" followed by the IP address of your machine. [. . . ] To print the network settings list: Press [Settings], [List], [Network Settings], then [Yes] At the command prompt on a network computer, type "ping" followed by the IP address of your machine. If the machine is active on the network, you will receive a replay. (Sample) NOTE: To run the command prompt: On Windows 98 Click Start Programs MS-DOS Prompt On Windows Me Click Start Programs Accessories MS-DOS Prompt On Windows 2000 and XP Click Start ALL Programs Accessories Command Prompt On Windows NT 4. 0 Click Start Programs Command Prompt On Windows server 2003 Click Start Command Prompt Installation Manual 19 Step 12: Browser-based setup Your machine can be set up from a browser. To access the machine's web page: 1 2 Type the machine's IP address in the URL address field of your browser. [. . . ]