User manual MYRYAD Z110

[. . . ] Myryad Systems Ltd 2 Piper's Wood Waterberry Drive Waterlooville PO7 7XU Tel +44 (0) 23 9226 5508 Fax +44 (0) 23 9223 1407 info@myryad. co. uk For further information, please contact Myryad direct or visit: www. myryad. co. uk Z-SERIES Z110 Remote Controlled CD Player Owner's manual contents · Introduction · Installation and Safety Notes · Accessories · Setting Up Your CD Player Rear panel connections introduction 2 2 2 3 4 5 6 6 7 7 The Z110 also has a "Smart My-Link" control input and output for communication with other Myryad Z-Series, Cameo or M-Series products. When linked via the "Smart My-Link" to a compatible Myryad integrated amplifier or preamplifier a number of extra features become available which make the system as a whole easier and quicker to operate. It is a full-function remote-controlled CD player. It has fixed-level low-impedance audio outputs to drive a Myryad integrated amplifier or pre-amplifier ­ or other high quality amplifier. [. . . ] To erase an entire program, press STOP to go into STOP mode and then press the CLEAR key and hold it down for about 2 seconds until the display reads "CLEAR". 5 4 Track number keys (0-9) Direct access to any track is possible using the numbered keys on the remote handset. track 26) press the track number keys "2" then "6". After the second key is pressed the player will play track 26. key "2") is pressed, the player will pause briefly before playing track 2. 3 My-Link input/output 5 Line outputs These outputs should be connected by high quality audio interconnects to the CD inputs of any integrated amplifier or preamplifier. Never connect to an amplifier's PHONO inputs. installing and replacing handset batteries The CD Remote Handset uses two 1. 5 V type AAA batteries. To fit new batteries first open the battery compartment in the rear of the handset and remove any existing batteries. Fit the new ones as directed by the symbols moulded inside the battery compartment, then replace the battery compartment cover. The batteries should always be removed if they are discharged (indicated by no remote control operation or by operation only at very short range), or if the remote control is not going to be used for an extended period. rear panel connections 1 Power inlet Before making any connection, check that the mains voltage setting printed on the rear panel is the same as your local mains supply. Plug the female (socket) end of one of the power cords supplied into the power inlet on the rear of each component. Plug the male (plug) end of each cord into a "live" wall socket or a suitable heavy duty extension cable. UK version: The mains plug is supplied fitted with a 5A fuse. My-Link is a communications bus that allows all the linked components to operate together as a system and distributes the remote commands received by any one to each of the others. The simplest function provided by the My-Link bus is that all linked units will switch into or out of standby mode when the amplifier or remote control standby key is pressed. Use a short RCA-to-RCA (phono-to-phono) interconnect cable to connect from the MYLINK OUT socket on the amplifier to the MY-LINK IN socket on the CD player. A second cable may then be run from the MY-LINK OUT socket on the CD player to the MY-LINK IN socket on a Myryad tuner ­ "daisy-chain" fashion. Further compatible Myryad products can be linked in the same way, running from the MY-LINK OUT socket on the tuner. Inexpensive interconnects may be used as the My-Link bus carries only control signals, not audio, so these cables have no effect on sound quality. When Myryad products equipped with "Smart My-Link" are connected via the MyLink bus, many more powerful system features are available (see page 7). z-series system operation with smart my-link When used as a linked system (e. g Integrated Amplifier plus CD Player, DVD Player and Tuner), Z-Series products have a number of extra features that make the system as a whole easier and quicker to use than a normal hi-fi. These include: Start-on-Play (CD, DVD): Press play on the CD or DVD Player (or the relevant remote control) and the player and Amplifier will switch out of standby (if necessary) and play the disc. The Amplifier will automatically select the appropriate source. 2 Power switch Press one side of this rocker switch (the side nearer the edge of the rear panel) to switch the CD player ON and the other side to switch it OFF. When the POWER switch is in the OFF position all power is disconnected from the CD player and it cannot be powered up from the front panel or the remote control. [. . . ] After about 4 seconds the display will revert to showing just track number "0". Table of Contents (Figure 2) PLAY and PAUSE The handset has separate keys for PLAY and PAUSE. Pressing PLAY from STOP mode will cause the disc to start playing. Subsequent pressing of PLAY whilst during PLAY mode will have no effect. [. . . ]