User manual MYRYAD Z130

[. . . ] Myryad Systems Ltd 2 Piper's Wood Waterberry Drive Waterlooville PO7 7XU Tel +44 (0) 23 9226 5508 Fax +44 (0) 23 9223 1407 info@myryad. co. uk For further information, please contact Myryad direct or visit: www. myryad. co. uk Z-SERIES Z130 Remote Controlled FM RDS Tuner Owner's manual contents · Introduction · Installation and Safety Notes · Accessories · Setting Up Your Tuner Rear panel connections introduction 2 2 2 3 4 6 6 7 7 7 7 When linked via the "Smart My-Link" to a compatible Myryad integrated amplifier or preamplifier a number of extra features become available which make the system as a whole easier and quicker to operate. The Z130 also has a "Smart My-Link" control input and output for communication with other Myryad Z-Series, Cameo or M-Series products. It is a full-function remote-controlled FM RDS Stereo Tuner. It has fixed-level lowimpedance audio outputs to feed a Myryad integrated amplifier or preamplifier, or other high quality amplifier. [. . . ] This will switch the STANDBY status of the Tuner without affecting any other unit. If Smart My-Link is being used the STANDBY and TUNER keys must be released simultaneously. setting up your tuner 5 4 3 My-Link input/output rear panel connections 1 Power inlet Before making any connection, check that the mains voltage setting printed on the rear panel is the same as your local mains supply. Plug the female (socket) end of one of the power cords supplied into the power inlet on the rear of each component. Plug the male (plug) end of each cord into a "live" wall socket or a suitable heavy duty extension cable. UK version: The mains plug is supplied fitted with a 5A fuse. It should only be replaced with a fuse of the same rating (5A) which complies with BS1362. system remote handset operation The Z130 Tuner is supplied with a System Remote Handset. which can also be used to control the Z140 Integrated Amplifier and Z110 CD Player. The System Handset keys allocated to control of the tuner are as follows: Preset, Manual and Search These keys allow direct access to any of the three tuning modes (see front panel MODE button). Tune up and tune down These keys operate exactly as the front panel TUNE UP/DOWN buttons. Mono and store These keys operate exactly as the front panel MONO and STORE buttons. DIM and number keys (0-9) These keys control the tuner but only when the handset is in "Tuner Mode". When you unfold the wire antenna you will note that it is in the form of a "T". The "crossbar" portion of the T should be stretched out horizontally and tacked in place, either on a wall or the back of a cabinet, or on the ceiling. The "vertical" section of the T goes to the tuner's antenna input via the balun. Experiment with the position and orientation of the antenna to obtain the best reception. 2 Power switch 9 Mono When the MONO button is pressed the tuner is locked into MONO reception mode and the STEREO indicator will not illuminate, whether the tuned station is transmitting in stereo or mono. The green LED next to the MONO button will illuminate to indicate this mode. If noisy reception is experienced in stereo mode, pressing the MONO button will usually result in a dramatic improvement in sound quality. When a station is stored as a preset (see below) the MONO status is also stored, and will therefore be recalled whenever that preset is accessed. installing and replacing handset batteries The System Remote Handset uses four 1. 5 V type AAA batteries. To fit new batteries first open the battery compartment in the rear of the handset and remove any existing batteries. Fit the new ones as directed by the symbols moulded inside the battery compartment, then replace the battery compartment cover. The batteries should always be removed if they are discharged (indicated by no remote control operation or by operation only at very short range), or if the remote control is not going to be used for an extended period. Press one side of this rocker switch (the side nearer the edge of the rear panel) to switch the tuner ON and the other side to switch it OFF. When the POWER switch is in the OFF position all power is disconnected from the tuner and it cannot be powered up from the front panel or the remote control. [. . . ] When the outputs are de-muted it will glow green continuously. When the STANDBY button is pressed again the component will be returned to standby mode, the STANDBY LED will glow red again and all other LEDs and the display will be extinguished. CAUTION: WHEN IN STANDBY MODE THE INTERNAL CIRCUITRY IS STILL LIVE, SO ALL SAFETY PRECAUTIONS MUST BE FOLLOWED. The infra-red (IR) remote control receiver is mounted behind this window in the position indicated. It must therefore not be obscured when the component is to be operated using the remote control handset. [. . . ]