User manual NAD HTR8 LEARNING REMOTE CONTROL

[. . . ] Eight DEVICE SELECTOR keys at the top—[AMP], [DVD, ] [TV, ] and so on - set the handset’s remaining keys to a “page” of commands to control a particular component. A DEVICE SELECTOR key determines only what component the HTR 8 will command; it does not perform any function on the component. All the remaining keys are function keys that can “learn” control codes from virtually any infrared remote controller, allowing you to teach the codes of your equipment, regardless of brand, to the HTR 8. Indd 3 20/01/2012 1:46a РУССКИЙ SVENSKA NEDERLANDS DEUTSCH with a full complement of NAD ITALIANO player to the [DVD] DEVICE SELECTOR ESPAÑOL remote control codes to be transmitted FRANÇAIS ENGLISH All of the function keys on the [AMP] R8_eng_OM_v03. [. . . ] Example: Copy the Pause command from the CD page to the AMP [j] button • On the HTR 8, simultaneously pressand-hold [AMP] and [RES]; the Learn LED turns steady green. € • • Press Pause [j]; the Learn LED turns amber. Press [CD]; press Pause [j]; the Learn LED turns green. Press [AMP] again to exit the learning mode. Note The copy and punch-through functions are similar. However, if you copy a command and then subsequently delete or overwrite the original (source-key) command, the copied-to key’s command remains unchanged. If you punch-through to a command and then delete or overwrite the original key, the punched-through functions also change accordingly. Macro Commands A “macro” command is a series of two or more remote codes issued automatically from a single keypress. You might use a macro to automate a simple command sequence, such as, “Turn on the DVD player and then press PLAY”. Or you might compose an elaborate macro to power up an entire system, select a source, choose a Listening Mode, and begin playback again, all from a single keypress. The HTR 8 can store one macro on each of its DEVICE SELECTOR and function keys. 20/01/2012 1:46a Note Macros are independent of the currently selected device. Recording Macros To record a macro, simultaneously press-and-hold for 3 seconds both the [MACRO] key and the HTR 8 function key to which you wish to assign the macro, until the status LED turns green. Press the sequence of function keys to be recorded into the macro, being sure to first press the requisite DEVICE SELECTOR key for each function (you may switch devices while recording the macro as create macro containing commands from more than one DEVICE SELECTOR “page. € When you have finished entering the desired command sequence, press [MACRO] again to store the macro; the Learn LED and [MACRO] key illumination Note Each macro can store a maximum of 64 command steps. If you exceed this number, the macro will be stored automatically after the 64th command is added. Example: Record a Macro to the [0] key to turn ON the NAD Receiver, turn ON the DVD Player, Select Input 1 (Source 1) and commence disc playback of connected Source 1 device (as in the DVD player) • On the HTR 8, simultaneously pressand-hold [MACRO] and [0] (numeric zero); the Learn LED turns steady green. € Press [AMP], press [ON]; press [DVD], press [ON]; press [AMP], press [1] (Input 1); press [DVD], press [4] (Play) – the Learn LED blinks as each step is added. Press [MACRO] again to exit the macro-record mode. To clear a macro, perform the above steps without entering any functions. ESPAÑOL many times as necessary), allowing you to FRANÇAIS ENGLISH Executing Macros R8_eng_OM_v03. Indd 8 ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ 8 To execute a macro, press and release [MACRO]; its key illumination lights for 5 seconds. [. . . ] 20/01/2012 1:46a Mode Learn/Copy/Punch Through Delete Mode Macro Record Library Mode Back Light Timeout Factory Reset Keys To Press (for 3 seconds) Device Key + RES Key Device Key + RTN Key MACRO Key + Function Key Device Key + A/V PSET Key DISP Key + Digit Key See “Factory Reset” above USB INTERFACE The HTR 8 allows one to upload and a Windows® PC and NAD’s Proprietary HTR 8 programming software. Use a USB A male to mini USB B male 5-pin cable (not supplied) between your Windows® PC and the HTR 8. See illustration below on how to connect a USB A male to mini USB B male 5-pin cable to the HTR 8. Your custom installer or dealer can assist you in the proper setup and configuration of the mini USB interface and software. [. . . ]