User manual NAD T787

[. . . ] ® Owner’s Manual AV Surround Sound Receiver T 787 РУССКИЙ SVENSKA NEDERLANDS DEUTSCH ITALIANO ESPAÑOL FRANÇAIS ENGLISH IMPORTANT SAFETY INSTRUCTIONS 1. Read instructions - All the safety and operating instructions should be read before the product is operated. 2. Retain instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the product and in the operating instructions should be adhered to. 4. Follow Instructions - All operating and use instructions should be followed. [. . . ] You can also press the [TEST] key to discontinue the ‘Test’ mode. In addition to the Volume knob, use the HTR 8’s [VOL D/F] to adjust the “master volume” of the T 787 raising or lowering the channels altogether. A momentary keypress will change the master volume by 1 dB increments. If you hold down [VOL D/F], the master-volume change will “run-on” until the key is released. Since recordings vary considerably in overall average level, there is no imperative to listen at any particular master-volume setting. A setting of -20 dB may sound “as loud” from one CD or DVD as -10 dB does from another. The T 787 will power-up from Standby mode at whatever master volume setting was last used; however, if the prior setting was greater than –20 dB, the T 787 will power up at –20 dB. This prevents inadvertently beginning a session at excessive volume. MUTING THE SOUND Use the HTR 8’s [MUTE] key to silence all channels completely. Muting is always available regardless of the source or listening mode selections. NOTES • Changing input or listening-mode selections does not release muting. • Adjusting the volume level via the HTR 8 or the front panel volume knob will automatically release the mute function. SPEAKER DISTANCE ADJUSTING THE VOLUME 23 РУССКИЙ SVENSKA NEDERLANDS DEUTSCH ITALIANO SETTING SPEAKER DISTANCE While at ‘Speaker Distance’ menu, use the [D/F] keys to individually set Front Left, Center, Front Right, Surround Right, Back Right, Back Left, Surround Left and Subwoofer to the distance measuring from your principal listening position to the front surface of their corresponding loudspeakers. Distance can be set up to 30 feet or 9. 1 meters Distance can be displayed as feet or meters selectable at the ‘Unit of Measure’ item. ESPAÑOL Your system’s speaker distance settings are a subtle but important refinement of your setup. Informing the T 787 of the loudspeaker-to-listener dimensions of each speaker automatically imposes the correct delays, optimizing imaging, intelligibility and surround-sound ambience. Enter your dimensions with precision within about 1 foot (30 cm). FRANÇAIS ENGLISH OPERATION USING THE T 787 – SETUP MENU ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH The Zone feature allows one to simultaneously experience in different zones of the house multiple sound sources from all enabled Sources as well as from Front Input, Media Player and Tuner. The T 787 has three configurable Zones – Zone 2, Zone 3 and Zone 4. Use a combination of [A/S/D/F] and [ENTER] keys to navigate through the Zone Setup menu parameters. If the surround back speakers are not used in the main zone, their surround back amplifier channels could be assigned for Main back, Main Front (BiAmp) and multi-zone use. The Surround Back amplifier is configurable through the following settings • Main Back: Assign as surround back speakers. • Main Front (Bi-Amp): Provide a bi-amp mode for the Main Front speakers (Left and Right) speakers thus reproducing the Front Left and Front Right amplifier channel outputs. • Zone 2: Assign the surround back amplifier channels to supply Zone 2 speaker level outputs from the surround back speaker terminals. • Zone 3: Assign the surround back amplifier channels to supply Zone 3 speaker level outputs from the surround back speaker terminals. [. . . ] • Check “Speaker Configuration” menu. • Select appropriate listening mode. • Correct “Speaker Configuration” or “Speaker Levels” settings. POSSIBLE SOLUTIONS • Check AC cable connection and outlet. Display shows “No Service List”. • DAB antenna not connected properly. [. . . ]