User manual NADY CT-6

[. . . ] SERVICE FOR YOUR NADY AUDIO PRODUCT (U. S. ) Should your NADY AUDIO product require service, please contact the Nady Service Department via telephone at (510) 652-2411, or e-mail at service@nady. com. (International) For service, please contact the NADY AUDIO distributor in your country through the dealer from whom you purchased this product. OWNER'S MANUAL DO NOT ATTEMPT TO SERVICE THIS UNIT YOURSELF AS IT CAN BE DANGEROUS AND WILL ALSO VOID THE WARRANTY. NADY SYSTEMS, INC. · 6701 SHELLMOUND STREET, EMERYVILLE, CA 94608 Tel: 510. 652. 2411 · Fax: 510. 652. 5075 · www. nady. com CT-6 6-Way Cable Tester 2/15/05, 12:33 PM CT6_manual 1 Cable Testing Phono to Phono 1 Sleeve 1 Sleeve 2 Hot 2 Hot 1/4" TS mono to Phono 1 Sleeve 1 Sleeve 2 Tip 2 Hot 1/4" TRS to Phono 1 Sleeve 1 Sleeve 2 Tip 2 Hot 3 Ring 2 Hot Phono to 1/4" TRS 1 Sleeve 1 Sleeve 2 Hot 2 Tip, 3 Ring 5-Pin DIN 1 1 2 2 3 3 4 4 5 5 2-pole SpeakonTM 1 (-1) 1 (-1) 2 (+1) 2 (+1) 4-pole SpeakonTM 1 (-1) 1 (-1) 2 (+1) 2 (+1) 3 (-2) 3 (-2) 4 (+2) 4 (+2) Introduction Congratulations for purchasing the CT-6 6-way cable tester. [. . . ] x2 RCA jacks XLR Balanced Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 male, 1 female SpeakonTM Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x2 Banana Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x2 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Steps Rotary Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9V DC Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5" x 3. 4" x 1. 5" (14 x 8. 6 x 3. 8 cm) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 4 lbs (0. 64 kg) 5 2 CT6_manual 2 2/15/05, 12:34 PM Controls and Connections 3) BATTERY CHECK LED -- Turn the rotary switch fully clockwise to test the battery strength. The battery LED indicator will light bright green if the 5 5 internal 9V battery is fully charged. The LED will get dim as the battery loses strength and turns off at approx 2V battery strength. 6 4) BANANA JACKS & LED -- Plug 6 2 3 each end of a single banana plug cable into the banana jacks. The LED will light 1 and the unit will beep a tone if there is a 7 connection between the plugs. The 7 banana jacks can also be used for continuity tests using two probe leads. 5) 1/4" JACKS -- For use with 1/4" TS 9 mono or TRS stereo/balanced plugs 8 6) 5-PIN DIN JACKS 7) PHONO JACKS -- For use with all standard Phono/RCA plugs 10 8) XLR FEMALE JACK 10 9) XLR MALE JACK 10) SPEAKON JACKS -- For use with 2-pole or 4-pole male Speakon connectors 11 11) BATTERY COMPARTMENT -- To replace battery, push up on the plastic 1) ROTARY SWITCH -- Selects the cable cover and remove the battery holder. [. . . ] If no LED lights than there is no connection and the left side contact "1" is "floating" due to design or an "open" in the cable. Set the rotary switch to "2" to test contact 2, and so on, until all contacts have been checked. 1/4" TS Mono to 1/4" TS Mono 1 Sleeve 1 Sleeve, 3 Ring 2 Tip 2 Tip 3 Ring 1 Sleeve, 3 Ring (shorted with sleeve) 1/4" TRS to 1/4" TRS 1 Sleeve 1 Sleeve 2 Tip 2 Tip 3 Ring 3 Ring XLR balanced to XLR balanced Pin 1 Pin 1 Pin 2 Pin 2 Pin 3 Pin 3 XLR unbalanced to XLR unbalanced Pin 1 Pin 1, Pin 3 Pin 2 Pin 2 Pin 3 Pin 1, Pin 3 1/4" TS Mono to XLR unbalanced 1 Sleeve Pin 1, Pin 3 2 Tip Pin 2 3 Ring Pin 1, Pin 3 (shorted with sleeve) 1/4" TRS to XLR balanced 1 Sleeve Pin 1 2 Tip Pin 2 3 Ring Pin 3 3 4 CT6_manual 3 2/15/05, 12:34 PM [. . . ]