User manual NADY PMC-2X

[. . . ] PMC2X_manual 3/3/04 4:49 PM Page 1 PMC-2X Specifications FRS radio IN/OUT jack: Impedances 1k / 16 Ohms Headphone Impedance: 16 or 32 Ohms PTT input jack: NO PTT SW Mic Impedance: 600 Ohms ­ Unidirectional AUX input jack: Stereo L+R inputs 10 / 10 Ohms Electret Condenser Controls: High / Low Volume adjust Housing Material: Cases and headset, both high impact ABS plastic button, OFF / Intercom switch Connectors: Passenger, Driver, Aux in, Ext. PTT, Size: 4. 0" x 2. 75" x . 65" (102 x 70 x 17 mm) 2-way Radio (3. 5mm TRS jacks); 5 VDC input, Weight: 3. 1 oz. (79 grams) 3. 5mm TS jack (TIP = NEG) Batteries: 3 AAA, 1. 5V Batteries Audio Output to Headphone: 150mW / 16-32 Ohms Specifications subject to change without notice PLEASE READ BEFORE USING YOUR PMC-2X Before you connect your intercom earphone and mic, it is important to make sure that the metal parts of the plug and jack are clean and dry, especially in cold weather. [. . . ] 6701 Shellmound Street, Emeryville, CA USA 94608 Tel: 510/652-2411 Fax: 510/652-5075 www. nady. com OWNER'S MANUAL MOTORCYCLE INTERCOM PMC2X_manual 3/3/04 4:49 PM Page 2 How to use the Nady PMC-2X Intercom with FRS Connection 1) Powering the PMC-2X: Place 3 fresh AAA, 1. 5 volt batteries into Battery Compartment (1), noting correct polarity. Alkaline batteries are recommended for long duration performance. If you wish to operate this unit with external power, plug the optional DC-5V adapter into the external DC Jack (2). Connect the other end of the adapter to your 12V DC motorcycle battery. 2) Connecting Your Headset: Insert both the driver and passenger headsets in the two Headset Jacks (3). 3) Intercom Only Operation: Flick INT/OFF switch (4) to "INT" position to turn on power. A power LED (5) lights to indicate the unit is in operation. 4) To Adjust Volume Control: Simply press the Volume Up (6) or Volume Down (7) buttons to achieve a comfortable listening level. You are now ready for full duplex, simultaneous two-way conversation. 5) External Music (Aux In) Operation: AUX IN: To add an external music source (Portable Tape/CD player, AM/FM radio) to the PMC-2X, use an ordinary stereo mini-phone plug jumper cable (3. 5mm TRS phone plugs both ends) and insert one end into the AUX IN jack (8). Connect the other end to your external sound source. For proper operation, please verify that the audio source has less then 200mW @ 8 ohms audio output power. Use the volume setting from the sound source to adjust the external audio to a comfortable listening level. + Stop here if you do not plan to connect the PMC-2X to an external FRS/GMRS or PMR 2-way radio or cell phone. Otherwise, proceed to section #6 for 2-way radio/ cell phone connection and operation. 6) PMC-2X/2-Way Radio/ Cellphone Connection and Operation: In order to operate your unit with your own FRS/GMRS or PMR 2-way radio or cell phone, please note the following: a. Your 2-way radio must have it's own internal VOX (voice activated transmission) function and a jack for connecting an external headset. [. . . ] (Your 2-way radio must have its VOX turned on to use this feature. ) You cannot use this PTT function with cell phones and do not need to as they are duplex already (simultaneous 2-way conversation like the intercom). (3) (5) (10) (9) (8) (6) (4) (7) Your PMC-2X is now ready for bike-to-bike communication with your riding partner(s) through your existing 2-way radio. Or even safe, convenient communication with anyone, while riding, through your cell phone. Note: Your 2-way radio should be kept at least 1" to 5" away from the PMC-2X to prevent possible RFI interference and ensure optimal operation. (1) (2) [. . . ]