User manual NADY RMX-6

[. . . ] 5 Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Model # ____________________________________________ SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Serial # ___________________ LEGAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 State _____________________ Zip _____________________ WARNING An equilateral triangle enclosing a lightening flash/arrowhead symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure which may be of sufficient magnitude to constitute a risk of electric shock. ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR An equilateral triangle enclosing an exclamation point is intended to alert the user to the presence of important operating and service instructions in the literature enclosed with this unit. IMPORTANT SAFETY INSTRUCTIONS When using this electronic device, basic precautions should always be taken, including the following: 1. [. . . ] The product should be serviced by qualified service personnel if: 11. Do not attempt to service the product beyond what is described in the user maintenance instructions. All other servicing should be referred to qualified service personnel. 3 INSTALLATION To ensure years of enjoyment from your NADY AUDIO RMX 6 please read and understand this manual thoroughly before using the unit. INSPECTION Your RMX 6 was carefully packed at the factory in packaging designed to protect the units in shipment. Before installing and using your unit, carefully examine the packaging and all contents for any signs of physical damage that may have occurred in transit. (Note: Nady Systems is not responsible for shipping damage. If the unit is damaged, do not return to us, but notify your dealer and the shipping company immediately to make a claim. Such claims must be made by the consignee in a timely manner. ) CONTENTS: · Instruction manual · SDP-20 (verify that the unit's serial number is same as shown on shipping carton) · AC Power cord · Warranty Card RACK MOUNTING The RMX 6 fits into one standard 19" rack unit of space (1 3/4"). Parts of the unit can become very warm during use. Care should be taken to ensure that there is enough space around the unit for cooling (at least 12" or 30cm). Do not place the RMX 6 on high temperature devices such as power amplifiers, etc. , or the unit may overheat in operation. Also, do not place the unit on speakers as this may cause them to move and/or fall due to speaker vibrations. Although the unit's chassis is shielded against radio frequency (RF) and electromagnetic interference (EMI), extremely high fields of RF and EMI should be avoided. POWER CONNECTION The RMX 6 has an internal power supply and is designed to operate from an external AC source. Power requirements for electrical equipment differ from area to area. Be sure to confirm that the voltage selected by the voltage selector switch on the back panel is proper for your area (120VAC/60 Hz or 230VAC/50Hz) per the information below: Europe (except UK): 230V, 50Hz UK and Australia: 240V, 50Hz USA and Canada: 120V, 60 Hz For other areas, please check with local authorities. When ready to operate, plug the AC cord into the power source. Make sure that the unit is turned off before connecting to the AC power source to avoid possible loud transients which can damage your speakers or your ears, especially when monitoring with headphones. 4 CONTROLS AND CONNECTORS FRONT PANEL (4) (3) (2) (1) REAR PANEL (5) (6) (7) (8) (9) Front Panel (1) POWER SWITCH Use this switch to power unit ON or OFF. The integrated LED will light when the unit is ON. Before turning on this unit, verify connection to the proper voltage AC source, check all connections and turn down the level controls of equipment connected to the outputs. (2) BASS & TREBLE TONE CONTROLS Adjust the relative balance of bass and treble (3) MASTER LEVEL CONTROL Adjusts the master level of the combined individual channel signals (4) CHANNEL GAIN CONTROLS Adjust the individual (1-6) channel gains Rear Panel (5) AC POWER CORD IEC CONNECTOR WITH INTEGRATED FUSE HOLDER This standard IEC power cord receptacle is used to connect the AC power to your unit. It features a built-in fuse holder for a 5X20mm, 0. 5A/250V slow-blow fuse. If the fuse continuously blows, shut of the unit and have it serviced by qualified service personnel. (6) AC VOLTAGE SELECT SWITCH Before plugging in the power cord, check to see that the unit is set for the proper voltage for your area: ~115V (60Hz) or ~230V (50Hz). (Note: Use at the improper voltage can damage your unit and (8) MIXER OUTPUTS Unbalanced 1/4" (6. 3mm) and balanced XLR outputs (Note: Only one output (1/4" or XLR) can be used at one time. Do not connect to both at the same time, or the signal will be severely distorted. ) (9) MIXER INPUTS Unbalanced 1/4"(6. 3mm) and balanced XLR inputs for channels 1 through 6. [. . . ] T250mA, 5X20mm glass type Dimensions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19" x 1. 75" x 8" (483 x 44 x 203mm) Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7. 0 lbs. ( 3. 2 Kg) The specifications above are correct at the time of printing of this manual. For improvement purposes, all specifications for this unit, including design and appearance, are subject to change without prior notice. LEGAL INFORMATION NOTICE The information in this document is subject to change, as the Company may make changes to product in order to improve reliability, design, or function, without prior written notice. [. . . ]