User manual NADY SCM 1000

[. . . ] NADY SCM SERIES TM SYSTEMS INC. USER GUIDE SCM 1000 Studio Condenser Microphones Congratulations on purchasing the Nady SCM 1000 FET Condenser Microphone. This superior microphone is perfect for recording studio vocals, acoustic instruments, orchestras and choral groups, ambient instrument audio, and many live sound applications. [. . . ] The SCM 1000 uses a carefully selected Field Effect Transistor (FET), specially chosen for its low distortion and superior signal-to-noise ratio. (Note: For optimum performance, it is best to let the microphone warm up for 5 to 10 minutes) The SCM 1000 is manufactured with the finest materials and features a machined housing with advanced internal shock mount construction for the highest structural integrity and rugged reliability. It requires 48V phantom power to operate, typically supplied by the microphone pre-amplifier or mixing console. The optional Nady SMPS-1 phantom power supply can also be used. WARNING The capsule is the heart of the condenser microphone. If it becomes dirty or wet, the sound will be degraded. Never spray any liquid on the microphone head. Always use a foam windscreen if you talk or sing close to the microphone grill screen. USING THE MICROPHONE SHOCK MOUNT The SSM-3 spider shock mount is available as an option for the SCM 1000. It uses an elastic suspension to isolate the Microphone from vibration, thereby lowering noise transmitted to the microphone from the stand. This is a useful tool in many situations, such as when the performer is tapping his or her feet, or when there is noise pickup from the rumbling of traffic outside of the building. The disadvantage of using the shock mount is that the weight of the microphone may make it drift in the elastic suspension, so mic placement may take a little longer. To insert the SCM 1000 into the SSM-3 shock mount, pinch close the levers on the sides of the mount to the open position, then slide the microphone into place. USING THE FOAM WINDSCREEN The FW-1 foam windscreen is available as an option for the SCM 1000. This windscreen fits over the grill portion of the microphone and is designed primarily to decrease bass rumble (from wind noise pickup) during outdoor live or recording use. [. . . ] Connect the SCM 1000 to the SMPS-1 Connect the SMPS-1 Signal Output to your mixer Connect the SMPS-1 to the AC power supply (115--230VAC) Turn on the SMPS-1 Power ON/OFF switch Slowly turn up the channel gain in your mixer to the desired level SERVICE (U. S. ) Should your Nady microphone require service, please contact the Nady Service Department via phone at (510) 652- 2411 or e-mail at service@nadywireless. com (INTERNATIONAL) For service, please contact the Nady distributor in your country through the dealer from whom you purchased this product. Do not attempt to service this unit yourself as it will void your warranty Date of purchase ___________________________________ Serial # ____________________________________________________________________________ Dealer's Name _________________________________________________________________________________________________________________________ Street _________________________________________________________________________________________________________________________________ City ______________________________________________ State ___________________________ Zip _______________________________________________ SCM 1000 SPECIFICATIONS Type: True condenser pressure-gradient microphone with 1. 1 inch diaphragm and FET pre-amplifier Polar pattern: Selectable Cardioid, ommidirectional and figure 8 Controls: Selectable low-cut filter and 10dB pad Open circuit sensitivity: 10mV/Pa=-40dBV (0dBV=1V/Pa) -10dB attenuation externally selectable Frequency range: 20 to 20, 000Hz Rated output impedance: < 200 Ohms Recommend load Impedance: 1000 Ohms Max. SPL (1% THD @1000Hz): 134dB Equivalent noise level to DIN 45405(CCIR468-2): 26dB IEC 268-4(A weighted): S/N ratio re 1Pa: Power requirement: Current consumption: Ambient temperature range: Relative humidity range: Connector: Phasing: 18dB-A 76dB +48VDC phantom power < 3mA 14°F to 140°F(-10°C to +60°C) 90%(68°F, 20°C), 85%(140°F, 60°C) 3-pin XLR (gold plated) Positive voltage on pin 2 relative to pin 3 Mic cable: 3-pin XLR standard cable (not supplied) Size: Diameter: 2. 1" (55mm), Length: 6. 5" (165mm) Net weight: 15oz (430g) Specifications and design subject to change without prior notice for improvement purposes 11/16/00 [. . . ]