User manual NAIM NAIT5

[. . . ] OWNERS MANUAL Integrated Amplifier page 1 1. 0 Equipment Installation 1. 1 cables and connections 2 2. 0 Getting Started 2. 1 2. 2 2. 3 2. 4 2. 5 3 switching on and off running in mains supply siting the equipment if you have a problem 3. 0 Warnings 4. 0 Connection 4 4. 1 mains lead 4. 2 non-rewireable mains plugs 4. 3 fuse carrier 4. 4 plug fuses 5 Nait 5 Integrated Amplifier Narcom 2 Remote Control Specifications, EC Declaration of Conformity to Appropriate Standards 10 12 1. 0 Equipment installation Normally your Naim equipment will have been installed by the dealer who sold it to you even if you live outside their immediate vicinity. Your dealer is responsible for making sure that the system sounds exactly as it should and information given here is not intended to reduce this responsibility in any way. 1. 1 cables and connections Please do not modify the standard interconnect cables supplied with your Naim equipment. This is important for safety as well as performance. One end of each cable is marked with a band to establish its correct orientation. [. . . ] The extra (left hand) socket is for use with separate phono stage, such as the Prefix or Stageline. Only one of these sockets may be used at a time, for safety as well as performance. Your amplifier will have a protective cover fitted over the extra socket. If you wish to use this socket it is advisable to refit the protective cover over the unused socket to prevent mistakes. tape facilities and monitor button The tape monitor (mon) button allows you to listen to the output of a 3-head tape machine while recording to check the "off-tape" signal. The source for recording is chosen by the input selector buttons in the normal way. Pressing the monitor button during recording allows the output from a 3-head tape machine connected to either tape, A/V or AUX 1 to be heard. After pressing "mon", select whichever one of these your tape machine is connected to. A second press returns the amp to normal position. mute button Pressing the mute button reduces the output from the loudspeakers to zero. (This will not affect any recordings taking place at the same time). balance adjustment Balance adjustment (left to right) on the Nait 5 is operated electronically within the amplifier. This is controlled by the remote handset. Please see separate instructions on page 10. Each of the inputs can be adjusted so that the volume level from all sources can be matched to one another. The remote handset enables this function. Some movement of the board and sockets when connecting/disconnecting is normal. 6 nait 5 connected to power supply input signal out A signal out B AUX 2 AUX 1 A/V tape tuner cd + - - + power to left loudspeaker ch1 to right loudspeaker mains input ch2 link plug fitted flatcap 2 power supply signal out A signal out B signal out C signal out D power out A power mains input for CD5, Headline or Stageline (additional interconnects required) Interconnect Cables 4 to 4 pin DIN 5 to5 pin DIN cable direction marker 7 nait 5 connected to power amp NB - do not connect nait 5 to mains in this configuration. input signal out A signal out B AUX 2 AUX 1 A/V tape tuner cd + - - + power amp + - - + input power to left loudspeaker ch1 to right loudspeaker mains input ch2 cable direction marker Interconnect Cables 4 to 4 pin DIN 5 to5 pin DIN 8 nait 5 connected to flatcap 2 power supply & power amp NB - do not connect nait 5 to mains in this configuration. input signal out A signal out B AUX 2 AUX 1 A/V tape tuner cd + - - + link plug fitted flatcap 2 power supply signal out A signal out B signal out C signal out D power out A power mains input power amp + - - + power to left loudspeaker ch1 to right loudspeaker mains input ch2 cable direction marker Interconnect Cables 4 to 4 pin DIN 5 to5 pin DIN 9 n2 System Component Keys Global Keys (Amplifier) Global Keys (CD Player) Global Keys (Tuner) Soft Keys narcom 2 remote handset NARCOM 2 is a multi-functional remote control handset designed to be used with Naim Audio CD players, integrated amplifiers, pre-amplifiers and preset tuners. The handset control configuration is based around three types of keys: System Component Keys, Global Keys and Soft Keys. 1 System Component Keys These keys switch the operation of the "Soft Keys" into modes appropriate to each system component (preamp, CD or tuner). preamp: Switches the action of the Soft Keys to that appropriate for an integrated or pre-amplifier. cd: Switches the action of the Soft Keys to that appropriate for a CD player. tuner: Switches the action of the Soft Keys to that appropriate for a preset tuner. 2 Global Keys These keys operate specific component functions regardless of the System Component Key setting. preamp vol (up and down): Adjusts the amplifier output volume and the volume control position. mute: Reduces the amplifier output volume to zero. The mute button on the amplifier will illuminate when mute is selected. bal (left and right): Adjusts the output channel balance. [. . . ] "-" indicates that the track can be selected. A space indicates that there is no more memory available. The prog key can also be used to delete tracks from a play order. To delete a track, press and hold the prog key until the prog indicator in the CD display illuminates then delete the track or tracks using the numeric keypad followed each time by a further operation of the prog key. [. . . ]