User manual NAIM SL2

[. . . ] WORLD CLASS HI FI OWNERS MANUAL Loudspeakers: SL2, allæ, Intro 2, axent, axess ISSUE 2 Introduction Naim Audio products are always conceived with performance as the top priority and careful installation will help ensure that their full potential is achieved. This manual begins with statutory safety warnings and general installation tips for all Naim Audio products. Product specific information begins in Section 6. CONTENTS Page 1 1 Equipment Installation 2 Cables and Connections 3 Getting Started 3. 1 switching on and off 3. 2 running in 3. 3 mains supply 3. 4 siting the equipment 3. 5 if you have a problem 4 Warnings 5 Connection 5. 1 mains lead 5. 2 non-rewireable mains plugs 5. 3 fuse carrier 5. 4 plug fuses 6 SL2 7 allæ, Intro 2, 8 axent, axess 1 Equipment Installation Normally your Naim equipment will have been installed by the dealer who sold it to you even if you live outside their immediate vicinity. Your dealer is responsible for making sure that the system sounds exactly as it should and information given here is not intended to reduce this responsibility in any way. 1 2 2 3 2 Cables and Connections Please do not modify the standard interconnect cables supplied with your Naim equipment. [. . . ] Stand it on the floor, plinth lowermost, and remove the top foam end-cap. Now move each Lower Cabinet with the Tweeter Suspension Assembly attached into the appropriate position. Take care not to place them so close to the wall that the rear spikes foul any carpet gripper that may be fitted. Also leave some space for final adjustment of the Tweeter Suspension Assembly and for the connecting cables. Adjust the spikes so that the cabinets are upright (a small spirit level will help) and do not rock. Tighten the lock-nuts with an appropriate spanner. Check again, once the lockTweeter Suspension nuts are tightened, that the Assembly cabinets do not rock on the spikes. Note: With thick carpet and underlay it can be difficult to ensure that the spikes are resting on the floor. Small slits cut into the carpet once the loudspeaker position is finalised will help. Pin Spacer 6. 4 SL2 Assembly Fit a Pin and a Spacer to the three holes in the aluminium top surface of each Lower Cabinet. There are two holes at the front and one at the back. Stage 3 The pack containing this manual also contains Cabinet Interface Pins and Cabinet Spacers. Fit a Pin and a Spacer to the three holes in the aluminium top surface of each Lower Cabinet. There are two holes at the front and one at the back. Spare Pins and Spacers are included in the pack. The Pins should be a loose fit in the holes. See Diagram 6. 4 Tweeter Adjustment Panel Upper Cabinet 6. 5 SL2 Assembly Take each Upper Cabinet in turn and carefully lower it onto the appropriate Lower Cabinet locating the Pins in the corresponding holes on its underside. At the same time as each Upper Cabinet is lowered onto each Lower Cabinet, the tweeter must be inserted through the back and front apertures of the Upper Cabinet. Now take each Upper Cabinet in turn and carefully lower it onto the appropriate Lower Cabinet locating the Pins in the corresponding holes on its underside. At the same time as each Upper Cabinet is lowered onto each Lower Cabinet, the tweeters must be inserted through the apertures of the Upper Cabinets. The loose fit of the Pins allows some adjustment of the alignment of the two cabinets. See Diagram 6. 5 5 SL2 Assembling and Installing SL2 (continued) It is vitally important for correct operation of SL2 that the Upper Cabinets are located properly on the Lower Cabinets, that the Pins are in place and that the two cabinets only touch via the spacers. The alignment of the Tweeter within the Upper Cabinets can be adjusted via either the two bolts connecting the Tweeter Suspension Assembly to the Plinth or the four screws that attach the Tweeter Adjustment Panel around the front face of the Tweeter. If the four adjustment panel bolts are loosened they should be re-tightened as securely as possible. As well as being adjusted to sit centrally when viewed from the front, and flush with the front panel, the Tweeter must oscillate freely without touching any part of either cabinet. [. . . ] Ensure that each positive plug - identified by a rib on the side of the cable and a tag marked "pos" on the side of the connector body - is inserted to the red input sockets. 7. 3 Speaker Components Upper Cabinet Lower Cabinet PIP 8 axent, axess 8 Introduction and Positioning Naim loudspeakers are precision acoustic instruments that will only achieve optimal performance if installed and set up carefully. Please read these instructions before installing and using the loudspeakers. Please also retain the packaging for future use. The performance of any loudspeaker will be influenced by the room in which it is located and even small changes of loudspeaker position can significantly influence the sound. [. . . ]