User manual NAPCO GEM-P3200

[. . . ] R PROGRAMMING INSTRUCTIONS HARDWIRE WIRELESS GEM-P3200 CONTROL PANEL/COMMUNICATOR GEMINI SYSTEM ARMED SYSTEM ARMED 01/01/00 12:00 AM 01/01/97 12:00AM ED ARM STA TUS NEXT/YES GEMINI SYSTEM ARMED 01/01/97 AC ON READY 12:00AM READY AC ON NEXT/YES GEMINI 48 A E RM A D ST TUS SYSTEM ARMED 01/01/97 12:00AMA1 ENT INTERIOR BYPASS FIRE/TBL SYS TBL CHIME A123 B456 D E F AREA PRIOR/NO A E RM DS TAT US A123 B456 D E AREA NEXT/YES C7 8 9 0 G COMPUTERIZED SECURITY SYSTEM R F PRIOR/NO A123 B456 D E AREA F PRIOR/NO C7 8 9 0 G COMPUTERIZED SECURITY SYSTEM R C7 8 9 0 G COMPUTERIZED SECURITY SYSTEM R GEM-RP1CAe2 GEM-RP2ASe2 GEM-RP3DGTL Quick Start: 1. Refer to the wiring diagram, connect the keypad(s), siren, aux. output, remote bus, earth ground, zone and telephone wiring. NOTE: See Installation Instructions (WI817). [. . . ] 4 ENTRIES blank (·) 1 2 3 4 5 6 7 8 9 0 B C D E F Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y NONE Note: "Y" indicates option is enabled. Note: "Y" indicates option is enabled. Note: "Y" indicates option is enabled. L NAPCO Security Systems X GEM-P3200 Programming Instructions !Page 26 WI818D 08/00 NOTES: * Minimum Level required to access function ** Level-3 Code with appropriate user option *** Requires Dealer Code USER OPTIONS OPTIONS Disabled Blocked View EXPLANATION User Code not active in this area. Allows User Code to block another code from being viewed by another user. An unblocked code cannot view a blocked code, but a blocked code can view all codes. The master user code and the dealer program code can view all codes. User Program Option is enabled for Keypad 1 only, wherever it is connected (any area). If enabled, Level 3 must also be enabled. This option, along with Level 3 Authorization, enables selection of OVERVIEW mode at a keypad. This Mode provides a system status display of all areas at a glance. Prevents User Code from disarming this area. A Service Code has restricted arm/disarm rights; if an area is armed with a Service Code, a "SERVICE ON" appears on the GEM-RP2ASe2 keypad (a "S" on the GEM-RP1CAe2 keypad) and the area can be disarmed with any valid User Code, including a Service Code. If the area is armed with OTHER than a Service Code, it CANNOT be disarmed with a Service Code. This is typically used to allow tradesmen access to premises under control of the owner. This is normally used to activate a door striker while an area is disarmed. A code with the access option will not function as an arm/disarm code. When the code is entered, the keypad will display "ENTER NOW" and the Brown Wire on the keypad will become Active Low (Ground Potential) for 7 seconds. USER AUTHORITY LEVEL LEVEL* 1 1 1 1 1 1 1 1 3 3** 1 2 3 3 1 *** *** *** 3 3 3 3 3 3 2 3 3** 3 1 1 KEYPAD DISPLAY FUNCTION MENU FUNCTION DISPLAY ZN FAULTS DISPLAY ZN BYPASSED DISPLAY ZN DIRECTORY ACTIVATE BELL TEST DISPLAY PHONE #'S DISPLAY SYS TRBL DISPLAY FIRE ALARM DISPLAY FIRE TRBL DISPLAY OP/CL ACTIVATE OVERVIEW ACTIVATE CHIME ACTIVATE WATCH RESET SYSTEM TRBL RESET SENSOR MSG START EXIT TIME FAULT FIND ACTIVATE LOCATE EZM ZONE FIND ACTIVATE DIALER TEST DISPLAY ALARM LOG DISPLAY TOTAL LOG DISPLAY FIRE LOG DISPLAY OP/CL LOG DISPLAY SYSTEM LOG AUTOARM IN 1-4HRS DISPLAY AUTARM SCHD ACTIVATE PROGRAM ACTIVATE DOWNLOAD DISPLY RF XMITTER STAT RELAY CONTROL User Program Bypass Overview Arm Only Service GEM-RP3DGTL Keypad: User Codes Access Related User Options: Ambush Code" (Address 0495), "Panel Access Code" (Address 0490), "Dealer Security Code" (Address 0500) & "Enable User Code by Area" (Address 2500-2547). !Press Jto save each code. To proceed to the next User Code, set the cursor to the User Number and change it using the number buttons. Program a new User Code as previously described. Press NEXT (E) button to proceed. Example: Program a code of "2222" for user 02, with User Option of "User Program", User "Level 3" and Access Control Option "Keypad No. Enter "2222" for a user code, "2 3" for user option and "blank(·) 1" for access control option. CHANGING OR CANCELING A CODE: To change any code, merely program over the existing code as described above and press Jto save. Similarly, to cancel a code, blank out each number of the code press Jto save to save. X GEM-P3200 Programming Instructions L NAPCO Security Systems WI818D 8/00 Page 27 15 INTERIOR BYPASS FIRE/TBL SYS TBL CHIME INTERIOR BYPASS FIRE/TBL SYS TBL CHIME (Direct Entry) RF Transmitter Points (Press the (A) button to set cursor. ) (For wireless systems only. Also see Quick Method, which follows) For each transmitter (key fob transmitters also), enter the zone number (01­48) to which the transmitter will be mapped, the 6-digit RF ID #:1-digit checksum number printed on the transmitter and box, the point number (1­4); enter "9" for unsupervised (all points). [. . . ] THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. THERE IS NO EXPRESS OR IMPLIED WARRANTY OF MERCHANTABILITY OR A WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. ADDITIONALLY, THIS WARRANTY IS IN LIEU OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF NAPCO. Any action for breach of warranty, including but not limited to any implied warranty of merchantability, must be brought within the six months following the end of the warranty period. [. . . ]