User manual NAPCO XP-400

[. . . ] $50(' 5($'< ' 6<67(0 Using Your XP-400 Security System =21( =21( =21( =21( NAPCO Oi220a page 1 Tuesday, September 16, 1997 08:30 2 Oi220a page 2 Tuesday, September 16, 1997 08:30 Introduction Congratulations on your purchase of an advanced NAPCO EXPRESS XP-400 Security System. Meticulously developed by a leading manufacturer of state-of-the-art security products, this system will provide you with unprecedented peace-of-mind & incorporates some of the most sophisticated features available today. Above all, it has been designed an extra step, to provide all those operating it with very easy, intuitive use. Please carefully review the information contained in this manual, so that you and all potential users of the system familiarize yourselves with its operation, and can therefore take full advantage of EXPRESS' many convenience features and amenities. Your system consists of a control panel (a computer housed within a white metal panel enclosure), one or more EXPRESS Decorator Keypads for controlling the system, and various security detection devices. [. . . ] Discuss these buttons with your installer. The emergency signal will only be activated when the two respective buttons are pressed at the same time. to alert the central station of an auxiliary Simultaneously press emergency, if so programmed. (The nature of this emergency alarm is to be determined by the installer) Yes to sound a police emergency alarm, and to alert Police Emergency: Simultaneously press the central station of a fire emergency, if so programmed. &+ + Ambush Alarm Enabled?Yes No Ambush Alarm In the event that you are forced by an intruder to disarm your system, the ambush alarm can be activated. Disarming the system with the Ambush Code will cause the system to disarm and simultaneously send a silent ambush alarm signal to Central Station. If your system has the Ambush feature enabled, the code assigned as the User 4 code will function as your Ambush Code. 8 Oi220a page 8 Tuesday, September 16, 1997 08:30 Disarming Your System / Silencing an Alarm Disarming Your System when Returning 1 ARMED READY SYSTEM Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to disarm the system before your Entry Delay time expires. The Red Armed light will go out, indicating that the system has been disarmed. Note: If you make a mistake entering your code, press the 2 Alarm Indication If the Red Armed light is flashing rapidly, an alarm occurred while you were away. For your own protection, leave immediately and call authorities from a neighbor's phone . ZONE 1 ZONE 2 ZONE 3 ZONE 4 Silencing an Alarm In the event that the system goes into alarm due to a violated burglary zone, the bell or siren will sound and the keypad sounder will also activate. To silence the system, enter your User code. The zone light of the is pressed to reset the alarm memory. zone which went into alarm continue flashing until 9 Oi220a page 9 Tuesday, September 16, 1997 08:30 Special Functions By pressing be enabled: Easy !f . f whi Bel f Access f f ollowed by the appropriate key, (do not press simultaneously) these special functions and features can Arm (when system is disarmed) The Easy Arm feature allows the system to be armed by ollowed by This will allow the easy pressing arming of the system by someone who is not a regular system user. Easy Exit (when system is armed) This function (if programmed) allows an occupant to leave the premises without disarming the system. Zone lights 1 through 4 will light to indicate any User Codes presently programmed. Programming / Reprogramming User Codes 1 Press the User number to be programmed. (For example, press 2 3 ZONE 1 ZONE 2 ZONE 3 ZONE 4 o program the User 2 code. ). The keypad will beep 2 times and the corresponding Zone light will flash to indicate the user number you are about to program. Press in the 4 digits of the new User 2 code, the keypad will beep 4 times. If there are more user codes to be programmed, return to step 1 above, otherwise, go to Exiting the User Program Mode below. t Erasing a User Code 1 Press the User number to be erased. The keypad will beep 2 times and the corresponding Zone light 2 Press will flash to indicate the user number you are about to erase. The zone light will go out to indicate that the user code has been erased. [. . . ] After repair or replacement, NAPCO assumes the cost of returning products under warranty. NAPCO shall have no obligation under this warranty, or otherwise, if the product has been repaired by others, improperly installed, improperly used, abused, altered, damaged, subjected to accident, nuisance, flood, fire or acts of God, or on which any serial numbers have been altered, defaced or removed. NAPCO will not be responsible for any dismantling, reassembly or reinstallation charges. This warranty contains the entire warranty. [. . . ]