User manual NAPOLEON GRILLS PRESTIGE V

[. . . ] This grill is designed for masonry, non-combustible enclosures only, and must be installed and serviced by a qualified installer to local codes. BUILT IN PROPANE GAS HOOK-UP: The piping up to the gas grill is the responsibility of the installer and piping should be located as shown in the built-in instructions. It must be connected with either rigid pipe, copper tube or an approved flexible metal connector. The installation must comply with CAN B149. 1 Natural Gas and Propane Installation Code in Canada, or to the National Fuel Gas Code, ANSI Z223. 1 in the United States. [. . . ] Access must be provided to the inside of the enclosure to make gas connections. OPENING DIMENSIONS 55 ¾" PF600 UNITS 46 ¾" PF450 UNITS 20 e" 7" 8 f" 2" MIN GAS INLET OPENING (4"x4") 6" 34" RECOMMENDED ELECTRICALWIREACCESS OPENING (4"x4") 8 ¼" 4" 8 ¼" ELECTRICAL BOX OPENING CENTER OF ELECTRICAL BOX MUST BE WITHIN 3 FEET OF LEFT EDGE OF GAS GRILL MINIMUM 10 SQ IN OF VENTILATION REQUIRED ON EACH END OF CABINET N415-0111 / NOV 29/05 BUILT-IN ACCESSORY OPENING DIMENSIONS D NOTE: ACCESSORY FRAMES OVERLAP OPENING BY 1 ½" ON ALL 4 SIDES H W Part # Description Picture OPENING DIMENSION W H 18 ¼" D N370-0069 Flat vertical painted door 13 ¼" N370-0071 Flat vertical stainless steel door 13 ¼" 18 ¼" N370-0070 Flat horizontal painted door 18 ¼" 13 ¼" N370-0072 Flat horizontal stainless steel door 18 ¼" 13 ¼" N370-0356SS Curved stainless steel door - 308 size 22 ½" 19 ¾" N370-0357SS Curved stainless steel door - 450 size 27" 19 ¾" N370-0358SS Curved stainless steel double door - 600 size 35 ¼" 19" N370-0361 PF style stainless steel door 17" 23 ¼" N370-0359 PF style stainless steel single drawer 17 ¼" 6 ¾" 23" N370-0360 PF style stainless steel triple drawer 17 ¼" 22 ¾" 23" OPTIONAL TRIM KIT N370-0362 ELECTRICALBOX N570-0046 1. Feed the wiring harness through the opening on the left hand side. Feed the gas flex connector and regulator down through the opening on the right hand side. Install the electrical box into the opening (fasteners not included). Feed the three white wires coming from the grill head into the hole in the back of the electrical box. Ensure the snap bushing is inserted into the hole. Feed the black electrical cord from the inside out through the same bushing. If you are connecting the power directly to the GFI outlet, disconnect the black electrical cord and use the same terminals on the GFI to connect the power. Attach the white wires to the transformer output. The two wires marked T2 to one output, and the one wire marked T1, to the other output. Plug the power cord into a suitable GFI protected outdoor outlet. For natural gas units, mount the regulator to the cabinet. Connect the gas supply to the inlet side of the regulator. For propane units, connect the gas supply to the end of the flexible connector. If using the optional trim kit, install the rear and side trim pieces using a dab of silicone. Leak test the entire installation before operating the unit. BUILT-IN ACCESSORY DRAWER INSTRUCTIONS 1. Remove the drawers from the enclosure by fully extending them and then lifting up to remove them from the slides. Shim the opening to ensure that the enclosure fits snuggly into the opening. Ensure that the side shims are located at the same height as the enclosure mounting holes. The bottom of the opening may need to be shimmed as well to ensure that the front of the enclosure is plumb. [. . . ] When the frame side wall is plumb, fasten it to the cabinet with screws (not provided). Attach the other side of the frame in the same fashion, ensuring the frame is square. Other than on the curved stainless steel double door kit, fasteners are not required on the top and bottom of the frame. The curved stainless steel double door frame must be fastened in the center both at the top and bottom. [. . . ]