User manual NAPOLEON GRILLS PTH10PSS

[. . . ] Tabletop Patio Heater (FOR OUTDOOR USE ONLY) PTH10PSS WARNING: For Outdoor Use Only. if odor continues , immediately call gas supplier. FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance. adjustment, alteration, services or maintenance can cause injury, death or property damage. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment. [. . . ] If disassembly is required, a leak test should be performed with soapy water upon re-assembly. This heater is designed to operate with a standard 1 LBs propane cylinder with Approved Cylinder Connection. The gas manifold supply pressure must be regulated at 11 inches water column utilising an approved regulator. The minimum inlet gas supply pressure for the purpose of input adjustment is 8 inches water column. The maximum inlet gas supply pressure is 13 inches water column. LP-gas supply cylinder is not provided with the appliance, statements that (1)the cylinder must be provided with a shut off valve terminating in an LP-gas supply cylinder valve outlet specified, as applicable, for connection No. 510 in the standard for compressed gas cylinder valve outlet and inlet connections, ANSI/CGA-V-I, or connection No. 600 in the compressed gas association's limited standard cylinder valve outlet connection for propane-small valve series. (2)the cylinder supply system must be arranged for vapor withdrawal; (3)the cylinder used must include a collar to protect the cylinder valve. if a connection No. 600 is used a statement that only cylinders marked "propane" must be used. 5 ASSEMBLY WARNING : TO BE INSTALLED ONLY BY AN AUTHORISED PERSON Step 1 ---- Attach Heater assembly to Base Attach heater assembly to base using 8-32 UNC L=6 (7 pcs) 2 1 10 Step 2 ---- Attach the Burner Column to the Hounsing Insert the clamp (3pcs) of the Burner Column into the spring piece (3 pcs) of Housing per the picture and screw over. Make sure the clamp and the spring piece fit together. 3 2 6 ASSEMBLY Step 3 ---- Attach Emitter Screen to Burner Column. Attach Emitter Screen to Burner Column using 8-32 UNC L=8 (3 pcs) Note: The ignition hole on emitter screen must li ne to the control knob. 3 Ignition Hole 9 3 Step 4 ---- Attach Reflector Dome and Dome Cap and Decorative Dome Cap Nut to Emitter Screen Attach reflector dome to emitter screen of the h eater assembly using 1/4-20 UNC washers (6 pcs) and 11 1/4-20 UNC nuts (3 pcs). Then attach dome cap and decorative dome cap nut to reflector dome. 12 8 7 12 5 7 ASSEMBLY WARNING : TO BE INSTALLED ONLY BY AN AUTHORISED PERSON Step 5 ---- Attach Emitter Screen shield to Burner Column Attach Emitter Screen shield to Burner Column . Of the heater assembly. 4 4 4 9 3 3 4 Step 6 ---- Connect Gas Hose, Regulator and Cylinder Attach gas hose to regulator. Attach regulator to cylinder. 1. Can connect to ILB portable cylinder dierctly. 2. Can also connect to 20 LB cylinder with regulator. 20 LB cylinder must binding to a table leg with a provided stretch line. 13 A table leg 8 ASSEMBLY WARNING : TO BE INSTALLED ONLY BY AN AUTHORISED PERSON Step 7 ---- Check for leak Your Patio Heater has been checked at all factory connections for leaks, To check the Connection of the gas hose/regulator/cylinder. 1) Make leak solution by mixing 1part liquid dish soap and 3 parts water. 2) Spoon several drops (or use squirt bottle) of the solution onto the gas hose/regulator and regulator/cylinder connection. 3) Inspect the connections and look for bubbles. 4) If no bubbles appear, the connection is safe. 5) If bubble appear, there is leak, loosen and re-tighten this connection. 13 Step 8---- Disconnect Cylinder When Storing or Transporting 1). Loosen the screw of cylinder and regulator. Disconnect the cylinder from regulator. 13 Caution: A leak test should be performed with soapy water whenever connecting a new cylinder. [. . . ] Never use flammable of corrosive cleaning agents. While washing your unit, be sure to keep the area around the burner and pilot assembly dry at all times. If the gas control is exposed to water in any way, do NOT try to use it. Keep controls, burner, and circulating air passageways clean. [. . . ]