User manual NAPOLEON GRILLS WATERFALLS

[. . . ] SERIAL / SÉRIE#______________________ DECORATIVE INDOOR WATERFALLS THAT PURIFY AND HUMIDIFY THE AIR WF 6/9/18 WF9ST MANUFACTURED BY / MANUFACTURE PAR: NAPOLEON APPLIANCE CORP. , 214 BAYVIEW DR. , BARRIE, ONTARIO, CANADA L4N 4Y8 PHONE: (705)726-4278 FAX: (705)725-2564 EMAIL: ask@nac. on. ca WEB SITE: www. napoleongrills. com RETAIN THIS MANUAL FOR FUTURE REFERENCE GARDER CE LIVRE POUR RÉFÉRENCES FUTURES N415-0128 / APR 30/06 NAPOLEON waterfalls are manufactured under the strict Standard of the world recognized ISO 9001-2000 Quality Assurance Certificate. NAPOLEON products are designed with superior components and materials, and are assembled by trained craftsmen who take great pride in their work. Every component is thoroughly inspected by a qualified technician before packaging and shipping to ensure that you, the customer, receive the quality product you expect from NAPOLEON. NAPOLEON WATERFALL PRESIDENT'S WARRANTY NAPOLEON warrants the materials and workmanship in your new NAPOLEON Waterfall against defects for a period of one year. This excludes filters, light bulbs, and UV light bulbs. [. . . ] Ensure that the wing nut on the side of the float valve is properly tightened. Connect the light wire to the terminals on the transformer. WATERFALL SURFACE MATERIALS The waterfall models WF6, WF9, and WF18 are supplied with a stainless steel panel for the water to flow over. The surface of the stainless steel must be cleaned to remove any grease or oily materials left behind from the manufacturing process. The protective coating will also leave a residue behind. Any residue left on the surface, or oily residue from your hands, will repel the water and prevent a sheet of water from forming over the panel. This will give you thin streams of water with large dry spots in between. Cleaning the panel with liquid TSP (or TSP Substitute) will remove any residue or film that is impeding the progress of the water. Clean the panel thoroughly two or three times before the first use. The See-Thru waterfall model is not supplied with any surface panel. The glass panel can be ordered from any glass and window dealer in your local area. There is no specific type of recommended glass, but the glass should be 1/4" thick. Clear glass displays the water flow pattern the best, but if privacy between the adjoining rooms is desired some type of smoked or opaqued glass will work as well. Before starting the waterfall, the entire panel surface should be wet down, either by spray bottle, or wet cloth. This will help the water to spread evenly across the panel. The wave effect of water flowing down the panel, will be attained after the panel is covered in water. The wave pattern can be adjusted by increasing or restricting the flow of water with the valve at the side of the filter. Adjust the valve to achieve the effect that is most pleasing to your eye. It is important to remember that too little water flow can cause dry spots to reappear on the surface of the waterfall. You can increase the flow of water slightly until they disappear. Lightly rubbing a wet cloth or Scotchbrite pad (careful not to scratch the stainless steel surface), across the panel may be enough to remove any dry spots. TO FOUNTAIN TO FOUNTAIN FROM BASIN FROM BASIN TO DRAIN TO DRAIN VALVE FULL OPEN VALVE PARTIAL OPEN GROOVED LUXIDIO PANEL: An optional grooved LUXIDIO panel which enhances the ripple effect can be purchased at your authorized NAPOLEON dealer. This panel must be cleaned with liquid TSP (or TSP Substitute) before being placed in the unit, to prevent dust and debris from the manufacturing process from entering the water. Use caution when cleaning the grooves on the panel as the machined edges can be very sharp. [. . . ] The parts must be shipped prepaid to the attention of the customer service department with the above information. Before contacting customer service, kindly note that the following items are not covered by the warranty: -costs for transportation, brokerage or export duties -labour costs for removal and reinstallation -costs for service calls to diagnose problems -discoloration of stainless steel parts -part failure due to lack of cleaning and maintenance, or use of improper cleaners. NOTES The rest of this page has been intentionally left blank. 8 FRAMING SPECIFICATIONS 2x6 HEADER PANEL RECOMMENDED CHECK WITH LOCAL CODES HEIGHT Ø1. 50" 4. 00" CENTERS 24" RECOMMENDED* CONTINUE DRYWALL UP TO THIS EDGE WIDTH CHECK WITH YOUR LOCAL BUILDING AUTHORITY FOR COMPLETE FRAMING GUIDELINES. THE CHART BELOW WILL GIVE YOU THE OPENING SIZE REQUIRED FOR EACH MODEL. EACH WATERFALL IS INTENDED TO BE MOUNTED ON TOP OF THE DRYWALL (NOT SHOWN). [. . . ]