User manual NAVMAN FISH 4150

[. . . ] FISH 4100 / 4150 Installation and Operation Manual English . . . . . . . . . . . . . c o m NAVMAN FCC Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a normal installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] · Calibrate the log, temperature and speed (4-6, 4-8). · Select the Trip Log or the Total Log (4-6). · Zero the Trip Log or zero all logs (4-6). · Adjust the display contrast(4-5). · Select language, setup keel offset and calibrate speed and temperature sensors (4-7, 4-8). Select MAIN MENU - SETUP to display the FISH 4150 SETUP Menu. Press or to select an option: 4-1 ALARMS menu Select MAIN MENU - SETUP - ALARMS to display the available alarms. Alarms can be enabled to automatically detect certain conditions, such as the water being too shallow. Trigger settings can be defined to suit the boat and individual preferences. The FISH 4100 ALARMS menu is shown: The FISH 4150 has two extra alarms, TEMP VALUE and TEMP RATE. The beeper cycle is different for some alarms. All of the alarm symbols and beeper cycles on the FISH 4100 are shown: Symbol Alarm Beeper Alarm condition is Name Cycle met when: 1/5 sec the depth is less than Too Shallow the alarm trigger value 1/2 sec Too the depth is greater Deep than the alarm trigger value Fish 3 short an echo matches the Alarm beeps profile of a fish 1/2 sec Low the battery voltage is Battery less than the alarm trigger value 14 The alarm symbols and beeper cycles for the two extra alarms on the FISH 4150 are shown: Symbol Alarm Beeper Alarm condition is Name Cycle met when: Temp 1/2 sec the temperature equals Value the alarm trigger value Temp 1/2 sec the rate of change of Rate temperature equals the alarm trigger value When an alarm condition is met, then: The beeper sounds. The ALARMS menu is displayed on the screen with the activated alarm symbol(s) flashing. Press any key to acknowledge the alarm, stop the beeping and remove the ALARMS menu. The symbol will continue to flash until the alarm condition is no longer present. Note: The FISH ALARM gives only three short beeps. · · Alarms automatically re-enable The TOO SHALLOW, TOO DEEP and LOW BATTERY alarms automatically re-enable when the value moves outside the alarm trigger setting. The TEMP VALUE alarm automatically re-enables when the temperature is more than 0. 45°F (0. 25°C) above or below the alarm trigger setting. The TEMP RATE alarm automatically re-enables when the rate of temperature change falls below the trigger setting by more than 0. 2°F (0. 1°C) per minute. FISH 4100 Installation and Operation Manual NAVMAN Flashing Light and/or External Beeper (FISH 4150 only) If a secondary alarm indicator is required, a flashing light and/or external beeper can be installed with a FISH 4150. These can be positioned anywhere suitable on the boat. For installation advice see section 5-4. Enabling Alarms and Changing Trigger Values Press or to highlight an alarm, then press select it. To enable or disable an alarm, press switch between ON and OFF. [. . . ] Ph: +86 20 3869 8784 Fax: +86 20 3869 8780 e-mail: sales@peaceful-marine. com Website: www. peaceful-marine. com OCEANIA AFRICA South Africa Pertec (Pty) Ltd Coastal, Division No. 16 Paarden Eiland Rd. Paarden Eiland, 7405 Postal Address: PO Box 527, Paarden Eiland 7420 Cape Town, South Africa. Ph: +27 21 511 5055 Fax: +27 21 511 5022 e-mail: info@kfa. co. za New Zealand Absolute Marine Ltd. Unit B, 138 Harris Road, East Tamaki, Auckland. [. . . ]