User manual NAVMAN FISH 4200

[. . . ] FISH 4200 F I S H F I N D E R S Installation and Operation Manual w w w. c o m NAVMAN FCC Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a normal installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] The water depth and the enabled alarms are shown at the base of the screen. Warnings: Fuel economy can change drastically depending on boat loading and sea conditions. Always carry adequate fuel for the journey plus a sufficient reserve. Each time fuel is added or removed use the fuel setup menu (see section 4-7) to record the fuel or else fuel remaining and the low fuel alarm will be meaningless! 14 NAVMAN FISH 4200 Installation and Operation Manual 3-9 RANGE menu Select MAIN MENU - RANGE to change the manual range and adjust the selected depth range. This shows the depth of water displayed vertically and the range mode setting. NAVMAN's FISH 4200 has two range modes, Auto Range and Manual Range. To change between Auto Range and Manual Range, press . The Manual Range mode offers the user a choice of pre-selected water depths. Use and to display the options and select a water depth. Press to exit. NAVMAN FISH 4200 Installation and Operation Manual 15 4 SETUP menu Select MAIN MENU - SETUP to display the SETUP menu: Use the SETUP menu to customize the FISH 4200 to suit the boat and individual preferences, as follows: specify the trigger settings for the alarms (see section 4-1) · choose the units for depth, temperature, speed and fuel (see section 4-2) · turn the key beep on or off (see section 4-3) · choose the fish symbol (see section 4-4) · choose the contrast level (see section 4-5) · select the Trip Log or the Total Log (see section 4-6) · zero Trip Log or zero all logs (see section 4-6) · sets the fuel options: tank full, set remaining, clear used (see section 4-7) · specify number of engines and tank size (see section 4-8) · select language, setup the keel offset (see section 4-8) · calibrate speed and temperature sensors (see section 4-8) · calibrate the fuel level and the fuel flow (see section 4-8) Press or to highlight an option, then see the following sections. · 4-1 ALARMS menu Select MAIN MENU - SETUP - ALARMS to display the available alarms. Alarms can be enabled to automatically detect certain conditions, such as the water being too shallow. Trigger settings can be defined to suit the boat and individual preferences. The beeper cycle is different for some alarms. All of the alarm symbols and beeper cycles are shown: When an alarm condition is met, then: the beeper sounds. the ALARMS menu is displayed on the screen with the activated alarm symbol(s) flashing. Press any key to acknowledge the alarm, stop the beeping and remove the ALARMS menu. The symbol will continue to flash until the alarm condition is no longer present. · · Symbol Alarm Beeper Alarm condition is Name Cycle met when: Temp 1/2 sec the temperature equals Value the alarm trigger value Temp 1/2 sec the rate of change of Rate temperature equals the alarm trigger value 1/5 sec Too the depth is less than Shallow the alarm trigger value 1/2 sec Too the depth is greater Deep than the alarm trigger value Fish 3 short an echo matches the Alarm beeps profile of a fish 1/2 sec Low the battery voltage is Battery less than the alarm trigger value Note: The FISH ALARM gives only three short beeps. NAVMAN FISH 4200 Installation and Operation Manual 16 Alarms automatically re-enable The TOO SHALLOW, TOO DEEP and LOW BATTERY alarms automatically re-enable when the value moves outside the alarm trigger setting. The TEMP VALUE alarm automatically re-enables when the temperature is more than 0. 45°F (0. 25°C) above or below the alarm trigger setting. The TEMP RATE alarm automatically re-enables when the rate of temperature change falls below the trigger setting by more than 0. 2°F (0. 1°C) per minute. Enabling Alarms and Changing Trigger Values Press or to highlight an alarm, then press select it. To enable or disable an Alarm, press switch between ON and OFF. To set the trigger value for an Alarm, press increase or decrease the trigger value. [. . . ] Consequently, the FUEL REMAINING value will be higher than the actual amount of fuel remaining in the tank. To avoid this problem, use the Auto Power Wiring option described in section 5. 4. This ensures that the fishfinder powers on automatically whenever the boat's ignition is switched on. b) In rough seas, fuel may surge back and forth through the fuel transducer, resulting in incorrect readings. [. . . ]