User manual NEC 84VM5 Installation Guide

[. . . ] 1 No Connection 2 RXD (Receive data) 3 TXD (Transmit data) 4 DTR (DTE side ready) 5 GND 6 DSR (DCE side ready) 7 RTS (Ready to send) 8 CTS (Clear to send) 9 No Connection 2) Connector on the external equipment side: Serial port (RS-232C) connector. See the specifications of the equipment that is to be connected for the type of connector and the pin assignment. 3) Wiring Use a crossed (reverse) cable. [. . . ] 9D 84 60 4E 00 CF The example of a change in the single mode of a 4th page multi-system configuration and the multi-mode is shown below. ID of the set used as a master(etc PC) is set to 50, and it assumes that ID is shaken by AUTO ID to each set. Upper left set (master) ID = 50 = 32h Upper right set ID = 51 = 33h Lower right set ID = 52 = 34h Lower left set ID = 53 = 35h Transmission Data DD 81 63 03 03 DD 82 63 03 03 DD 83 63 03 03 DD 84 63 03 03 03 03 03 03 01 02 03 04 00 00 00 00 CB CD CF D1 Transmission of the above command performs a 4th page multi SPLIT display. Moreover, the following commands are published in order to change a 4th page multi-display into a single mode display. DF 80 60 03 03 01 01 00 C7 All sets become a single mode display by the above-mentioned command. Since this command does not specify Set ID, all sets execute it. *:Control by ID may not be able to be performed depending on connection with external control apparatus. www. necvisualsystems. com Page 8 of 14 NEC Solutions (America), Inc. Visual Systems 84VP5/84VM5 Installation Guide (using four 42VM5 or 42VP5 Plasma Displays) (also a reference for optional Quad Mount used with 42VM5 or 42VP5) Command Codes 01. Power ON Function The external control equipment switches on the power of the plasma monitor. Transmission Data 9FH 80H 60H 4EH 00H CKS ACK The plasma monitor returns the following ACK when the power is switched on. 3FH 60H 80H 4EH 00H CKS NOTE: Do not set the Power ON or Power OFF command continuously. v1. 3 02. Power OFF Function The external control equipment switches off the power of the plasma monitor. Transmission Data 9FH 80H 60H 4FH 00H CKS ACK The plasma monitor returns the following ACK when the power is switched off. 3FH 60H 80H 4FH 00H CKS NOTE: Do not set the Power ON or Power OFF command continuously. 03. Input Switch Change Function The external control equipment switches the input of the plasma monitor. Transmission Data DFH 80H 60H 47H 01H DATA00 CKS DATA00 : Input Select 01H : Video1 02H : Video2 03H : Video3 05H : HD (HD1 or DTV or DTV1) 06H: HD2 (DTV2 or SCART1/SCART2) 07H : RGB1 / PC1 08H : RGB2 / PC2 0CH : RGB3 / PC3 0DH : HD3(SCART3) ACK The plasma monitor returns the following ACK when the input is switched. AUDIO Mute ON Function The external control equipment switches on AUDIO Mute of the plasma monitor. Transmission Data 9FH 80H 60H 3EH 00H CKS ACK 3FH 60H 80H 3EH 00H CKS 05. AUDIO Mute OFF Function The external control equipment switches off AUDIO Mute of the plasma monitor. [. . . ] Transmission Data DFH 80H 60H F3H 03H DATA00 DATA01 DATA02 CKS DATA00: 011 screen (Matrix display function does not work. ) 044 screens (2*2 video wall) 09H9 screens (3*3 video wall) DATA 01: DATA 02: 00H-FFMaster's *1 01H : Video1 02H : Video2 03H : Video3 04H : HD (HD1 or DTV or DTV1) 05H : HD2 (DTV2) 06H : HD3 (DTV3) 07H : RGB1 / PC1 08H : RGB2 / PC2 09H : RGB3 / PC3 *: This command is used to following system. The system configuration is video wall system (4screens or 9screens). The ID number from a master1 display is set the continuous number. [. . . ]