User manual NEC GT60 INSTALLTION GUIDE V32S

[. . . ] Distances are in inches, for millimeters multiply by 25. 4. Distances may vary ±5%. · · Formulas The Projection Formulas use the image width for calculation. Image width is the same for all aspect ratios, only vertical image size varies. [. . . ] If 3D Reform is not used, the approximate range of Vertical Position is +/-0. 167H (H=Screen Height) when using a 16:9 screen. This adjustment is only available when the projector is set for `16:9', `1. 85:1' or `2. 35:1' in the `Screen' menu. X=Distance from lens to mount ctr Shift Range + GT12ZLB: X=16. 1" GT19ZLB: X=12. 0" GT20ZL: X=12. 5" GT24ZLB: X=12. 4" GT34ZLB: X=12. 0" GT48ZLB: X=14. 0" Lens Centered with Mount Note: GT10RLB, GT19ZLB & GT34ZLB are set back inside shroud. Screen Ctr Desktop Setup Note: Lens shift is not available on GT06RLB & GT10RLB rear lenses, which should only be used for "zero degree/nooffset" applications. Note: Tilting the front of the projector up or down by more than 45° from level could reduce lamp life by up to 20%. C Throw Distance Screen Ctr 5. 3" Note: GT10RLB, GT19ZLB are set back inside shroud. Distance chart for popular 16:9 screens Rear Lenses Zoom Lenses Screen Size (16:9) DIAG inches GT06RLB GT10RLB 0. 6:1 inches GT12ZLB 1. 2 - 1. 7:1 inches GT19ZLB 1. 7 - 2. 2:1 inches GT20ZL 2. 0 - 2. 6 inches GT24ZLB 2. 2 - 3. 2:1 inches GT34ZLB 3. 2 - 4. 8:1 inches GT48ZLB 4. 8 - 7. 1:1 inches W inches H inches 1. 0:1 inches 92 100 106 110 119 123 133 135 159 161 229 275 367 459 80 87 92 96 104 107 116 118 139 140 200 240 320 400 45 49 52 54 58. 5 60 65 66 78 79 113 135 180 225 47. 1 51. 5 54. 6 57. 0 NA NA NA NA NA NA NA NA NA NA 78. 2 85. 2 90. 2 94. 2 102. 3 105. 3 114. 3 116. 3 137. 4 138. 4 198. 6 NA NA NA 93. 4 - 135. 0 101. 8 - 147. 1 107. 8 - 155. 7 112. 7 - 162. 6 122. 3 - 176. 3 125. 9 - 181. 5 136. 7 - 197. 0 139. 1 - 200. 4 164. 4 - 236. 6 165. 6 - 238. 3 237. 8 - 341. 7 285. 9 - 410. 6 NA NA 132. 7 - 175. 9 144. 6 - 191. 5 153. 1 - 202. 7 159. 9 - 211. 7 173. 5 - 229. 6 178. 6 - 236. 3 193. 9 - 256. 5 197. 3 - 261. 0 233. 1 - 308. 0 234. 8 - 310. 2 336. 8 - 444. 6 404. 9 - 534. 1 NA NA 156. 2 - 205. 9 170. 2 - 224. 3 180. 2 - 237. 4 188. 2 - 247. 9 204. 2 - 268. 9 210. 2 - 276. 8 228. 3 - 300. 4 232. 3 - 305. 6 274. 3 - 360. 7 276. 3 - 363. 4 396. 4 - 520. 8 476. 5 - 625. 7 NA NA 172. 6 - 256. 5 252. 5 - 386. 2 188. 1 - 279. 4 275. 3 - 420. 6 199. 2 - 295. 7 291. 5 - 445. 2 208. 0 - 308. 8 304. 5 - 464. 8 225. 8 - 334. 9 330. 4 - 504. 1 232. 4 - 344. 7 340. 1 - 518. 8 252. 4 - 374. 1 369. 3 - 563. 1 256. 8 - 380. 7 375. 8 - 572. 9 303. 4 - 449. 3 444. 0 - 676. 1 305. 6 - 452. 5 447. 2 - 681. 0 438. 7 - 648. 6 641. 9 - 975. 8 527. 4 - 779. 2 771. 7 - 1172. 3 704. 9 - 1040. 6 1031. 2 - 1565. 4 NA 1290. 8 - 1958. 4 381. 3 415. 9 440. 6 460. 3 499. 8 514. 6 559. 1 569. 0 672. 7 677. 6 974. 0 1171. 5 1566. 7 1961. 8 - 569. 5 - 620. 5 - 657. 0 - 686. 1 - 744. 4 - 766. 3 - 831. 9 - 846. 5 - 999. 5 - 1006. 8 - 1444. 1 - 1735. 7 - 2318. 8 - 2901. 9 Note: For screen sizes not indicated on the chart, use the formulas on page 1. Note: "NA" means it is outside the screen range for that lens. Refer to "Screen Sizes" in Lens Specifications on Page 1. www. necvisualsystems. com GT5000/6000 Page 3 of 10 Lens Shift Adjustable Range The top right diagram shows the location of the image position in the lens. The lens can be shifted within the shaded area as shown using the normal projection position as a starting point. Maximum Possible Range for GT12ZLB/GT20ZL/GT48ZLB lenses: *Values for 16:9 screens in parentheses. Up: 0. 5H (0. 67H) Down: 0. 5H (0. 67H) Right: 0. 32W Left: 0. 32W H=Height of image (take care to use appropriate value for 4:3 or 16:9 screens) W=Width of image Note: Lens shift is not available on GT06RLB & GT10RLB rear lenses, which should only be used for "zero degree/no-offset" applications. Note: If the lens is shifted in two directions combined, maximum range in either direction cannot be obtained due to rounded off area of lens. (example: shift up and right) See top right diagram. 0. 32W 0. 32W W Note: The diagram below shows a 4:3 image as an example. 0. 5H (0. 67H) Desktop/Front Vertical 0. 5H (0. 67H) H H Normal position Normal projection position 0. 5H (0. 67H) Ceiling/Front Vertical Normal position 0. 32W W 0. 32W H 0. 5H (0. 67H) Normal position Warning: · Installing the projector on the ceiling must be done by a qualified technician. · Tilting the front of the projector up or down by more than 45° from level could reduce lamp life by up to 20%. · Only use the projector on a solid, level surface. If the projector falls, you could be injured and the projector severely damaged. · Do not use the projector where temperatures vary greatly. The projector must be used at temperatures between 32°F (0°C) and 95°F (35°C). · Do not expose the projector to moisture, dust or smoke. This will reduce the quality of the image. · Ensure that you have adequate ventilation around the projector so heat can dissipate. [. . . ] For hardware contact Display Devices at 303-412-0399. www. necvisualsystems. com GT5000/6000 Page 9 of 10 Input Panel AUDIO AUDIO OUT AUDIO SLOT1 DVI SLOT2 USB(B) USB(A) PC CARD 2 1 AUDIO RGB2 PC CONTROL IN LAN REMOTE1 RGB OUT OUT SC TRIGGER REMOTE2 IN OUT VIDEOS-VIDEO AC IN RGB1 AUDIOAUDIO AC SW Control Codes Function Code Data POWER ON 02H 00H POWER OFF 02H 01H INPUT SELECT RGB 1 02H 03H INPUT SELECT RGB 2 02H 03H INPUT SELECT VIDEO 02H 03H INPUT SELECT S-VIDEO 02H 03H INPUT SELECT DVI (DIGITAL) 02H 03H INPUT SELECT VIEWER 02H 03H LAN 02H 03H SLOT 1-1 02H 03H SLOT 1-2 02H 03H SLOT 2-1 02H 03H SLOT 2-2 02H 03H RGB1(VIDEO) 02H 03H RGB1(S-VIDEO) 02H 03H PICTURE MUTE ON 02H 10H PICTURE MUTE OFF 02H 11H SOUND MUTE ON 02H 12H SOUND MUTE OFF 02H 13H ON SCREEN MUTE ON 02H 14H ON SCREEN MUTE OFF 02H 15H ASPECT RATIO 1. 25:1 (5:4) 03H 10H 1. 33:1 (4:3) 03H 10H 1. 78:1 (16:9) 03H 10H 1. 85:1 03H 10H 2. 35:1 03H 10H AUTO ADJUST 02H 0FH Note: Contact your NEC rep for codes not listed. 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 02H 02H 02H 02H 02H 02H 02H 02H 02H 02H 02H 02H 02H 00H 00H 00H 00H 00H 00H 05H 05H 05H 05H 05H 02H 02H 03H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 12H 13H 14H 15H 16H 17H 18H 18H 18H 18H 18H 05H 01H 02H 06H 0BH 1AH 1FH 20H 24H 25H 29H 2AH 07H 0CH 09H 0AH 0EH 13H 22H 27H 28H 2CH 2DH 31H 32H 0FH 14H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 18H 00H 01H 02H 03H 04H 00H 00H 00H 00H 00H 30H 31H 32H 33H 34H Cable Connection Communication Protocol: Baud Rate: 38400 bps Data Length: 8 bits Parity: No Parity Stop Bit: One bit X on/off: None Communications: Full duplex 1 2 67 3 8 4 9 To RTS of PC To CTS of PC 5 PC Control Connector (D-Sub 9P) To TxD of PC To RxD of PC To GND of PC NOTE1: It is recommended to set the projector to "Idle Mode" in the Setup menu for best Power ON response. NOTE2: Pins 1, 4, 6, and 9 are used inside the projector. [. . . ]