User manual NEC GT950

[. . . ] English GT950 LCD Projector User's Manual SO U R C E A AD UT O JU ST S T PO AT U O WE S NR /S TA N D BY M EN U SE LE C T E N TE CA NC EL LE NS SH IFT FO C U S ZO O M E­1 R IMPORTANT INFORMATION Precautions Please read this manual carefully before using your NEC GT950 Projector and keep the manual handy for future reference. Your serial number is located under the name plate label on the left side of your GT950. Record it here: This label is on the side of the remote control. CAUTION CAUTION To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. CAUTION TO PREVENT SHOCK, DO NOT OPEN THE CABINET. [. . . ] This function also adjusts the clock phase to reduce video noise, dot interference or cross talk. (This is evident when part of your image appears to be shimmering. ) This adjustment may be necessary when you connect your computer for the first time. NOTE: The Auto Adjust function does not work for component signal. E ­ 31 Volume control: Sound level from the speaker and AUDIO OUTPUT mini jack on the projector can be adjusted. Sound is not available when PC Card Viewer is selected. Using Pointer You can use one of eight pointers to draw your audience's attention to the portion of a projected image you want. POINTER VOLUME increase volume Volume bar Press the Pointer button to display the pointer. decrease volume Turning off picture and sound: Press the Picture Mute button to turn off the image and sound for a short period of time. Press again to restore the image and sound. SELECT PIC-MUTE Use the Select button to move the pointer. Enlarging and Moving a Picture You can enlarge the area you want up to 400 percent. To do so: Getting Help about how to operate the projector: You get the contents about Help. HELP 1. Press the Pointer button to display the pointer. POINTER SELECT Display Help 2. Move the pointer to the area you want to enlarge. Exit Help SELECT 3. When the Magnify (+) button is pressed, the pointer is changed to a magnifying glass. To move the magnifying glass, use the Select button. MAGNIFY E ­ 32 4. Return the image to the original size. MAGNIFY Using the Menus NOTE: The on-screen menu may not be displayed correctly while interlaced motion video image is projected. 1. Press the "Menu" button on the remote control or projector cabinet to display the Main Menu. NOTE: When using a USB mouse, click the mouse button to display the main menu. For other operations, do the same way as you use your PC mouse. 2. Press the buttons on the remote control or the projector cabinet to highlight the menu for the item you want to adjust or set. Correcting Keystone distortion Press (+) or (-) to correct keystone (trapezoidal) distortion to make the top or bottom of the screen longer or shorter so that the projected image is rectangular. 3. Press the button or the "Enter" button on the projector cabinet or the remote control to select a submenu or item. Adjust the level or turn the selected item on or off by using "Select" or buttons on the cabinet or the remote control. The onscreen slide bar will show you the amount of increase or decrease. Changes are stored until you adjust it again. ENTER . . . . . . . . . Return to the previous screen without storing settings or adjustments. NOTE: You can close the main and sub menus simultaneously by pressing the PJ button to cancel the Projector mode. KEYSTONE Keystone distortion Normal 6. Repeat steps 2-5 to adjust an additional item, or press "Cancel" on the projector cabinet or the remote control to quit the menu display. NOTE: The maximum keystone angle that can be corrected is 30 degrees upward and 30 degrees downward with the projector placed horizontally on the ground plane. [. . . ] · Use the Keystone to correct the trapezoid distortion. · Reposition the projector to improve its angle to the screen. · Ensure that the distance between the projector and screen is within the adjustment range of the lens. · Use menus or a source button on the remote control or the cabinet to select the source you want to input. [. . . ]