User manual NEC HIVID 3500

[. . . ] MultiSync Hivid 3500 Projector Large Screen MultiSync Projection System User's Manual Model number: XL-3500 CAUTION: To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. GSGV Acoustic Noise Information Ordinance: The sound pressure level is less than 70 dB(A) according to ISO 3744 or ISO 7779. Precautions Please read this manual carefully before using your NEC MultiSync Hivid 3500 Projector and keep the manual handy for future reference. WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY INSERTED. [. . . ] 7 9 5 4 3 3 4 3 5 8 5 7 /01/1998 /01/2000 /01/2040 Output CTL+5 Data:List No. xxx To select a source using the INPUT buttons on the remote control when no menus are displayed: 1) Press the INPUT "0" button. · The Select Terminal menu is displayed. 2) Use the CURSOR or button to select an input terminal you wish to input. 3) Press the ENTER button to execute selection and to switch to the selected input. To cancel, press any one of the INPUT buttons. INPUT SELECT List Format Page / total pages ­ sheet No. Connect condition of the Switcher PO1/10-1 No 01 02 03 04 05 06 07 08 09 10 Name NTSC 78K NTSC No40 No39 31. 45K A Source Source VIDEO RGB V R R R V V IDEO GB GB GB IDEO IDEO Select StandAlone Input A A C A A A C B No. xxx Option PO1/10-2 No Dat 01 02 03 04 05 06 07 08 Jan 09 Jan 10 Jan e Source fh Select StandAlone fv 60. 07 72. 28 6 6 7 5 5 5 0 0 5 9 1 1 . 0 5 1 9 8 9 7 2 0 6 5 2 Key CTL+10 15. 74 78. 36 1 3 3 3 1 1 5 7 7 1 5 5 . 7 9 5 4 3 3 4 3 5 8 5 7 /01/1998 /01/2000 /01/2040 Output CTL+5 Output Data:List Data:List No. xxx Signal name Rgistered input module Horizontal Frequency Entry date Vertical Frequency Input terminal Output data for the signal currently projected. 30 3. OPERATION NOTE: · While you are viewing a source screen, you can also select the input signal directly by pressing the INPUT "1" through "10" button. In this case INPUT buttons function as follows: When using the projector in stand alone operation: Input Mode Input Module A RGB 1 VIDEO 2 S­VIDEO 3 COMPONENT 4 COMPONENT (HDTV) 5 Slot Selection 10 Numbers designate INPUT buttons on the remote control. When using the projector with the ISS-6020/ISS-6020G: INPUT 1 through 10 Selects the corresponding number slot of the ISS-6020/ISS-6020G When using the projector with two ISS-6020/ISS-6020G or more: To switch to another input signal, enter the master slot number, then the slave slot number by using INPUT buttons and press ENTER. Example:If you want to select a signal from the no. 3 slot of the slave Switcher which is connected to the no. 2 slot of the master Switcher, first press the INPUT "2" button, then the INPUT "3" button and then press ENTER. · You can switch to any input signal of NO 01 through10 on the Source Select list by holding down the CTL button and pressing one of the INPUT buttons corresponding to the input number. To activate this function you must first select ENABLE in the Direct Key. For further details, contact your dealer. · If there are two or more memory locations that contain the same signal information the projector will reference the signal nearest the beginning of the list. To select the next signal use the CURSOR or button and press ENTER. 31 3. OPERATION Source Information Provides and changes information for the parameters of your current projected source. NOTE: For other registered signals, change their parameters on the Source Registry menu. The menu items you can display, change or specify are as follows: Source Name--------------- Changes a user name that has previously been entered. Direct Key ------------------ Assigns settings of source to each INPUT button (1-10) with CTL. Input Slot ------------------- Selects an input terminal for the registered signal when you need to do due to adding optional equipment. Signal System -------------- Displays the signal system of the current source such as RGB, Video, SVideo, or Component signal. [. . . ] 2 User the CURSOR or button to highlight the test pattern you wish to use and press ENTER. · The selected test pattern will be displayed. 3 To return to the original screen, press TEST and then press END. · When the TEST button is pressed, the Test Pattern menu will be displayed and when END is pressed, the screen will be changed to the source screen. [. . . ]