User manual NEC IDC-3000

[. . . ] NEC Improved Definition Converter IDC-3000 NEC Improved Definition Converter IDC-3000 User's Manual R NEC Technologies, Inc. 1255 Michael Drive Wood Dale, Illinois 60191 Printed in Japan 79TM0282 WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. [. . . ] The selected video signal is output when RGB input has been selected and MONITOR button is switched on. Connected to the H/V input jack of a monitor or projector having a 31. 5 kHz horizontal scanning function. Connected to the audio input jacks of RGB equipment. 0 HV POL. Switch Selects the polarity of the horizontal and vertical output signals. Active low A PC-CONTROL SW (Switch) Selects the communications standard of the PC-CONTROL connector. RS-232C standard 9 RGB Output Connector (OUTPUT) RGB (BNC) . . . . . . . . . . . . . . . . . . . . . . Connected to the RGB input jacks of a monitor or projector having a 31. 5 kHz horizontal scanning function. Connected to the HORIZONTAL input jack of a monitor or projector having a 31. 5 kHz horizontal scanning function. Connected to the VERTICAL input jack of a monitor or projector having a 31. 5 kHz horizontal scanning function. B AC IN Receptacle Used to connect the supplied power cord. C PC-CONTROL Connector (15-pin connector) Connect to a personal computer or other control equipment. D EXTERNAL CONTROL Connector Connections are made to this connector when controlling this unit by external control. (See the "External Control Mode" section. ) RGB (D-Sub 15 mini) Connector Pin Assignment Pin No. 6 5 4 10 9 3 8 2 7 1 Signal to be connected Red input Green input Blue input GND GND Red GND Green GND Blue GND Open Sync GND GND Open H-Sync V-Sync Open 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 15 14 13 12 11 NOTE : · Use a signal conforming to the standard TV signal when connecting an input source. · Using poor quality video tape may cause distortion on the picture. A B REMOTE CONTROL 1 POWER Button Turns the power on or off. 2 VIDEO 1 Button Switches the unit to the video 1 input mode. 1 3 2 7 9 C E POWER 4 5 MONITOR 3 VIDEO 2 Button Switches the unit to the video 2 input mode. VIDEO1 VIDEO2 VIDEO3 VIDEO4 VIDEO5 RGB 6 0 8 B F 4 VIDEO 3 Button Switches the unit to the video 3 input mode. SPLIT NOISE REDUCTION 5 VIDEO 4 Button Switches the unit to the video 4 input mode. MOVIE STILL D A NORMALIZE MODE1 MODE2 UP DOWN 6 VIDEO 5 Button Switches the unit to the video 5 input mode. 7 RGB Button Switches the unit to the RGB input mode. REMOTE CONTROL UNIT RD-338E 8 MONITOR Button Used to switch on the monitor mode at the time of RGB input. 9 SPLIT Press to activate the demonstration split mode function for processing the artificial interlace and switching off the 3-dimensional Y/C separation processing the right half of the screen. This function is for use when the NTSC indicator is lit. 0 NOISE REDUCTION Button Used when screen noise becomes annoying. Each time this button is pressed, the NR function will change as follows: OFF NOISE REDUCTION 1 NOISE REDUCTION 2 (Noise is reduced) (Noise is further reduced) E MODE 2 Button Used to select the image system. Each time this button is pressed, mode 2 will change as follows: SPLIT MOVIE · SPLIT . . . . . . . . . . Selects the demonstration split mode function for processing the artificial interlace and switching off the 3dimensional Y/C separation processing the right half of the screen. This function is for use when the NTSC indicator is lit. Selects the Y/C separation method and the image interpolation method. Mode Normal Movie 1 Movie 2 Movie 3 Y/C Separation Motion adaptation Move mode Move mode Motion adaptation Image Interpolation Motion adaptation Move mode Motion adaptation Move mode A MOVIE Button Press to manually set the method of Y/C separation and image interpolation. B STILL Button Press to display still images such as those from document cameras, etc. The Y/C separation and image interpolation will be set for the still screen mode. C NORMALIZE Button Sets the various adjustments to the standard settings (which had been set at the factory prior to shipping). D MODE 1 Button Selects image adjustment and audio adjustment. Each time this button is pressed, mode 1 will change as follows: COLOR TINT SHARPNESS SOUND F DOWN and UP Buttons Used to adjust or activate the item selected with the MODE 1 or MODE 2 button. C D REMOTE CONTROL NOTES Remote Control Precautions The remote control system may not function when direct sunlight or strong illumination strikes the remote sensor window of the main unit. Do not place in locations where there is a high temperature or high humidity. When remote control buttons are pressed and held, main unit operations may not be possible. Battery Precautions Do not use new and old batteries together. [. . . ] If you are uncertain as to whether a dealer is authorized, please contact NECTECH at (708)-238-7764. Any product on which the serial number has been defaced, modified or removed. Damage, deterioration or malfunction resulting from: a. Accident, misuse, abuse, neglect, fire, water, lightning or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the products. [. . . ]