User manual NEC LT10

[. . . ] Portable Projector LT10 Users Manual FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Trademarks Trademarks are the rights of their respective owners. Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Setting 10 will maximize brightness and contrast. Setting 0 will maximize color reproduction quality. Color Temperature Adjust the color temperature. At higher temperature, the screen looks colder; at lower temperature, the screen looks warmer. Keystone Adjusts image distortion caused by tilting projection (±16 degrees). Zoom Press the Press the to reduce the size of an image. to magnify an image on the projection screen. & User Controls Computer / Video Mode -nglish All Images Aspect Ratio Selects the desired aspect ratio. Reset This Menu Choose "Yes" to return the display parameters on this menu to their factory default settings. ' -nglish User Controls Computer Mode Computer Image Auto Adjust The projector automatically adjusts clock, phase, horizontal and vertical. With most signal sources, Auto Adjust provides the best results. Clock "Clock"changes the display data frequency to match the frequency of your computer's graphic card. If you experience a vertical flickering bar, use this function to make an adjustment. Phase "Phase" synchronizes the signal timing of the display with the graphic card. If you experience an unstable or flickering image, use this function to correct it. Horizontal Press the Press the to move the image left. to move the image up. Vertical Press the Press the Reset This Menu Choose "Yes" to return the display parameters on this menu to their factory default settings. User Controls Video Mode -nglish Video Image Color Adjusts a video image from black and white to fully saturated color. Press the Press the to decrease the amount of color in the image. to increase the amount of color in the image. Sharpness Adjusts the sharpness of the image. Press the Press the to decrease the sharpness. to increase the sharpness. Hue Adjusts the color balance of red and green. Press the Press the to increase the amount of green in the image. to increase the amount of red in the image. Reset This Menu Choose "Yes" to return the display parameters on this menu to their factory default settings. -nglish User Controls Computer / Video Mode Setup Menu Location Choose the Menu location on the display screen. Orientation Front-Desktop The factory default setting. Rear-Desktop When you select this function, the projector reverses the image so you can project behind a translucent screen. Front-Ceiling When you select this function, the projector turns the image upside down for ceiling-mounted projection. Rear-Ceiling When you select this function, the projector reverses and turns the image upside down at same time. You can project from behind a translucent screen with ceiling mounted projection. Lamp Hour Meter Displays the lamp's elapsed operating time (in hours). Clear Lamp Hours Meter Turns the lamp hour counter to 0 hours. Reset This Menu Choose "Yes" to return the display parameters on this menu to their factory default settings. User Controls Computer / Video Mode -nglish Setup Factory Default Choose "Yes" to return the display parameters (except for Lamp Hours) on all menus to their factory default settings. ! -nglish User Controls Computer Mode PIP Picture-In-Picture PIP Choose "On" to turn the PIP screen on. PIP Location Choose the PIP screen position on the display screen. PIP Switch Source Choose the input source of the projector on the PIP screen. The OSM does not include a PIP menu under Video mode. Reset This Menu Choose "Yes" to return the display parameters on this menu to their factory default settings. " Appendices Troubleshooting If you experience trouble with the projector, refer to the following information. If the problem persists, please contact your local reseller or service center. Problem: No image appears on screen. Ensure all the cables and power connections are correctly and securely connected as described in the "Installation" section. Ensure the pins of connectors are not crooked or broken. Check if the projection lamp has been securely installed. Please refer to the "Changing the lamp" section. [. . . ] Service Options: There are 3 types of "Service" available. Enduser has to understand following condition and is required to fill in the Application Sheet. 1) Repair and Return: The 'Faulty unit' is sent or collected from the customer. It is repaired and returned within 10 days to the customer, excluding transport time. [. . . ]