User manual NEC LT150

[. . . ] NEC MultiSync LT150 / LT85 User's Manual Micro-Portable Projector MultiSync LT150/LT85 User's Manual Printed in Japan 7N8P0051 DECLARATION OF CONFORMITY This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. No. : Type of Product: Equipment Classification: Models: NEC Technologies, Inc. [. . . ] Turn off the power to the projector and VCR, laser disc player or document camera. Connect one end of your RCA cable to the video output connector on the back of your VCR or laser disc player, connect the other end to the Video input on your projector. Use an audio cable (not supplied) to connect the audio from your VCR or laser disc player to your audio equipment (if your VCR or laser disc player has this capability). Be careful to keep your right and left channel connections correct for stereo sound. Turn on the projector and the VCR or laser disc player. NOTE: Refer to your VCR or laser disc player owner's manual for more information about your equipment's video output requirements. E­25 About Startup screen (Menu Language Select screen) When you first turn on the projector, you will get the Startup screen. This screen gives you the opportunity to select one of the seven menu languages: English, German, French, Itilan, Spanish, Swedish and Japanese. To select a menu language, follow these steps: 1. Use the Select v or w button to select one of the seven languages for the menu. 2. Press the Enter button to execute the selection. The Basic/Custom menu will be displayed in the language you have selected. To close the menu, press the Cancel button. After this has been done, you can proceed to the advanced menu operation. If you want, you can select the menu language later. See "Language" on page E-40. E­26 3. OPERATION Connecting the Power Cable and Turn on the Projector Before you turn on your projector, ensure that the computer or video source is turned on and that your lens cap is removed. To turn off the projector: First press the "POWER" button on the projector cabinet or the remote control for a minimum of two seconds. After the projector turns off, the cooling fans keep operating for 90 seconds. NOTE: Do not disconnect the power cable during this time. Status of indicator light: turn on M EN U 1 Connect the supplied power cable to the projector. CA N CEL S E LE C stand by STATUS POWER AC IN ENTER T O S N/ TA N D B Y S O U R C E P C C A R D A A UT DO JU A C S C T E S S ON/STAND BY S TA TU P O S W E R RD CA PC steady orange light flashing 3 to 5 minutes STATUS POWER EO VID O IDE S-V B RG PC DIO AU L RO NT CO B US steady light STATUS POWER flashing green light steady green light Plug the supplied power cable in the wall outlet. The projector will go into its standby mode and the power indicator will glow orange. Status of indicator light: turn off ON STATUS POWER ON/STAND BY press a minimum of two seconds 2 Turn on and off the Projector steady green light POWER ON/STAND BY button SOURCE AUTO ADJ. S TA TU S P O W E cooling down STATUS POWER stand by STATUS POWER ME NU Vol. R /D NN O TA S B Y SELECT change to flashing green light steady orange light S O U R C E ER CA POINTER CE N L Vol. Indicator To turn on the projector: Only after you press the "POWER" button on the projector cabinet or the remote control will the power indicator turn to green and the projector become ready to use. NOTE: To turn the projector on by plugging in the power cable, use the menu and enable the "Auto Start" feature. (See page E-42. ) NOTE: Immediately after turning on the projector, screen flicker may occur. Wait 3 to 5 minutes until the lamp lighting is stabilized. ME ER CA CE N L EN MAGNIFY HELP POWER T PIC. [. . . ] · · · · · Check the card remote control. If the insulation tape remains, remove it. See page E-13 or E-16 Make sure there are no obstacles between you and the projector. Stand within 22 feet (7 m) of the projector. [. . . ]