User manual NEC LT55 QUICK GUIDE

[. . . ] Quick Connect Guide Step1 Connect the supplied signal cable. LT155/LT154 ST CE AT SS PO US W ER MultiSync LT156/LT155/LT154 Step3 Turn on the projector. Adjusting the Tilt Foot 1. Press the Tilt button on the front of the projector to extend the Adjustable Tilt Foot. M EN U Mini D-Sub 15 pin connector AC IN ME NU SE LE CT AU AD TO JU ST PC CO NT RO VID L EO S-V IDE O RG AU DIO S E LE C T B DIO CA ENTER Audio cable (not supplied) US B PC CO P AC CC S CE AR TA S D TU S P O S W E R AU RD S O U R C E A A UT DO JU S T CAN CEL RGB cable (supplied) RG B DE AU DIO O ST N/ AN D O S-V IDE O RG BY US B PC AC BI CA RD C CA RD ENTER SO UR CE CANCEL NP UT O S N/ TA N D B Y DVI connector x DVI-D ­ DVI-D signal cable (supplied) ME NU L VID EO S-V ID LT156 SE LE CT ST CE AT SS PO US W ER CA RD C CA RD ENTER NOTE: To turn off the projector, press and hold the Power (ON/STAND BY) button for a minimum of two seconds. 1 2 AC IN SO UR CE CANCEL AU AD TO JU ST AC PC IN CO NT RO VID L EO S-V IDE O DV I-D EO S-V IDE O AU DIO O ST N/ AN D DV DV BY US B PC AC I AU DIO I-D AU DIO Step4 Set up the Projector Audio cable (not supplied) Mini D-Sub 15 pin connector RGB cable (supplied) DVI-A ­ VGA adapter (supplied) To adjust the projector's focus or to zoom in and out, use the Focus ring and Zoom lever on the lens. 3. Lower the front edge of the projector to the desired height and release the Tilt button to lock the Adjustable Tilt Foot. S ENTE E LE C T AU ME N DIO U RG O B S VID NTR OL EO E -VID Zoom lever · PC CA RD US B P O CC AC IN Focus ring Power cable (supplied) ME Step2 Connect the supplied power cable. 4 3 AC IN U N AC IN If the projected image does not appear square to the screen then use keystone correction for proper adjustment. [. . . ] The RGB2 button is not available on LT155/LT154. On LT156 the RGB1 button selects DVI digital input; the RGB2 button selects DVI analog input. Auto Adjust Button (RGB only) Adjusts the current image for optimal H/V position, Pixel settings and resolutions. PJ Button Press this button if you want to use the Mouse (LM ), Cancel/Right Click, and Enter/Left Click buttons as your PC' s. Laser Button Press and hold this button to activate the laser pointer. Menu Button Displays the menu for various settings and adjustments. Mouse (LM When you are in the Computer mode, these buttons work as a computer mouse. Enter / Left Click Button When you are in the Computer mode, this button works as the mouse left button. Cancel/ Right Click Button When you are in the Computer mode, this button works as the mouse right button. Pointer Button Points to an area on screen to be magnified. Advanced Menu Source Select Picture Volume Image Options Projector Options Tools Help RGB Video S-Video PC Card Viewer Brightness / Contrast / Color / Hue / Sharpness * High-Bright / Eco Normal / Natural 1 / Natural 2 Volume Keystone Color Temperature Lamp Mode Gamma Correction Advanced Options Factory Default Normal / Zoom / Wide Zoom / Cinema Aspect Ratio Noise Reduction Off / Low / Medium / High Select Color Matrix: HDTV/SDTV Color Matrix Select Color Matrix Type: B-Y/R-Y, Cb/Cr, Pb/Pr Brightness R/G/B, Contrast R/G/B White Balance Horizontal / Vertical / Clock / Phase Position/Clock Auto / Native Resolution On / Off Video Filter All Data / Current Signal Menu Mode (Advanced Menu, Basic/Custom Menu) Basic/Custom Menu Edit Language (English/German/French/Italian/Spanish/Swedish/Japanese) Projector Pointer (Pointer 1-8) Source Display (On / Off) Direct Button Volume Bar (On / Off) Keystone Bar (On / Off) Menu Display Time (Manual/Auto 5 sec / Auto 10 sec / Auto 30 sec) Page 1 Orientation (Desktop Front / Ceiling Rear / Desktop Rear / Ceiling Front) Background (Blue / Black / Logo) Mouse Button (Right Hand / Left Hand) Sensitivity (Fast / Medium / Slow) Page 2 PC Card Viewer Options Show Folder List (On / Off) (Auto Play / Manual Play) Interval (5-300 sec) Capture Options (High Quality/Normal/High Compression) Page 3 Signal Select RGB (Auto/RGB/Component) Video (Auto/NTSC3. 58/NTSC4. 43/PAL/PAL60/SECAM) S-Video (Auto/NTSC3. 58/NTSC4. 43/PAL/PAL60/SECAM) Page 4 Auto Adjust (RGB Only) (On/Off) Auto Start (On/Off) Power Management (On/Off) Power Off Confirmation (On/Off) Keystone Save (On/Off) Clear Lamp Hour Meter Page 5 Communication Speed (4800/9600/19200/38400) Default Source Select (Last/Auto/Select) (RGB /Video/S-Video/PC Card Viewer) 1 2 14. Help Button Displays information for the current menu or how to use the menu. OFF ON Menu Setup 4 VIDEO S-VIDEO AUTO ADJ. 3 6 RGB 1 RGB 2 PJ 15. Keystone (+) (­) Button Corrects for keystone (trapezoidal) distortion to make the image square. Magnify (+) (­) Button Magnifies image size up to 400%. Press again to resume motion. Capture PC Card Files ChalkBoard 5 7 MENU LASER 9 10 8 ** 18. Picture Mute Button Turns off the image and sound for a short period of time. Press again to restore the image and sound. [. . . ] Printed in Japan 7N8P0223 11 (Underneath) 13 R-CLICK /CANCEL HELP POINTER PC CARD 12 20 KEYSTONE MAGNIFY SLIDE 14 15 16 FREEZE VOL. FOLDER *** 21 22 PIC-MUTE SLIDE Contents Information Contents Page1 Source Name / Input Terminal / Horizontal Frequency / Vertical Frequency / Sync Polarity Page2 Signal Type / Video Type / Sync Type / Interlace / Resolution Page3 Aspect Ratio / Gamma Correction / Noise Reduction / Color Matrix / Matrix Type Page4 Lamp Remaining Time / Lamp Hour Meter / Projector Usage 17 18 LIST 23 19 NOTE: "DVI (DIGITAL)" * On LT156, "DVI (ANALOG)" and "DVI (ANALOG)" are displayed in the Source Select submenu. is displayed in the Signal Select ** On LT156, "DVI (DIGITAL)" and "DVI (ANALOG)" can be also on Page 3. [. . . ]