User manual NEC LT75Z

[. . . ] Micro-Portable Projector LT75Z English User's Manual Deutsch Français Italiano Español Svenska IMPORTANT INFORMATION Precautions Please read this manual carefully before using your NEC LT75Z Projector and keep the manual handy for future reference. Your serial number is located on the bottom of your LT75Z. Record it here: CAUTION To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. [. . . ] In most cases signal cannot be output from RGB output unless the notebook PC is turned on after connecting with the projector. NOTE: * If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power management software. * If you accidentally hit the POWER button on the remote control, wait 90 seconds and then press the POWER button again to resume. NOTE: If using video, S-video, or audio cables, the cables should be 3 m (9. 8 feet) or shorter. To connect SCART output (RGB) Before connections: An exclusive SCART adapter (ADP-SC1) and a commercially available SCART cable are required for this connection. NOTE: Audio signal is not available for this connection. Video equipment such as DVD player Projector 3. Turn on the power to the projector and your video equipment. Use the RGB button on the remote control to select the RGB input. Press the MENU button on the remote control to display the menu. From the Advanced menu, select [Projector Options] [Setup] [Signal Select RGB] [Scart]. ADP-SC1 SCART is a standard European audio-visual connector for TVs, VCRs and DVD players. It is also referred to as Euro-connector. Commercially available SCART cable Female 1. Turn off the power to the projector and your video equipment. Use the NEC ADP-SC1 SCART adapter and a commercially available SCART cable to connect the RGB input of your projector and a SCART output (RGB) of your video equipment. NOTE: The ADP-SC1 SCART adapter is obtainable from your NEC dealer in Europe. Contact your NEC dealer in Europe for more information. E-16 Connecting Your PC or Macintosh Computer IBM VGA or Compatibles (Notebook type) or Macintosh (Notebook type) S TA TU S E R / N O TA S N D B Y P O W PC CO NT RO L AU DIO S O U R C E A U TO A D JU S T ME RGB signal cable (supplied) To mini D-Sub 15-pin connector on the projector. It is recommended that you use a commercially available distribution amplifier if connecting a signal cable longer than the supplied one. Audio cable (not supplied) VID EO S-V IDE O N U S E ENTE R LE C T RG B CAN CEL AU AU DIO DIO VID EO RG S-V IDE O BI NP UT RG B IBM VGA or Compatibles (Desktop type) Macintosh (Desktop type) NOTE: The new Macintosh computer such as G3 will have the 15 pin HD connector. The LT75Z's "Plug and Play" data will be downloaded to the Macintosh. Therefore, a Mac adapter will not be necessary. DIP ON 1 3 4 5 6 2 For older Macintosh, use a commercially available pin adapter to connect to your Mac's video port. Pin adapter for Macintosh (not supplied) Connecting your PC to your LT75Z (SVGA) projector will enable you to project your computer's screen image for an impressive presentation. To connect to a PC or Macintosh computer, simply: 1. Turn off the power to your projector and computer. Use the supplied signal cable to connect your PC or Macintosh computer to the projector. If the projector goes blank after a period of inactivity, it may be caused by a screen saver installed on the computer you've connected to the projector. E-17 Connecting Your DVD Player DVD player S TA TU S E R /D NN O TA S B Y P O W PC CO NT RO L AU DIO S O U R C E AU R A U TO A D JU S T ME DIO L Co m Y pon Cb ent Cr AU DIO VID EO S-V IDE O N U S E ENTE R LE C T RG B CAN CEL VID EO RG S-V IDE O BI NP UT RG B Optional 15-pin-to-RCA (female) 3 cable (ADP-CV1) Component video cable RCA 3 (not suplied) Audio Equipment AU R DIO L Audio cable (not supplied) You can connect your projector to a DVD player with component outputs or Video output. [. . . ] Ensure your cables are connected properly. Use menus to adjust the brightness and contrast. Reset the settings or adjustments to factory preset levels using the Factory Default in the Adjustment Menu. See page E-29. No picture Image isn't square to the screen · Reposition the projector to improve its angle to the screen. [. . . ]