User manual NEC MT1000

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual NEC MT1000. We hope that this NEC MT1000 user guide will be useful to you.

Lastmanuals help download the user guide NEC MT1000.

Download

Manual abstract: user guide NEC MT1000

Detailed instructions for use are in the User's Guide.

 [. . . ] NEC Multimedia Theatre

NEC Multimedia Theatre

NEC Technologies,  Inc. Arlington Heights Road, Suite 500 Itasca,  Illinois 60143-1248

LCD Projector User's Manual
®
Part No. 78408201 Printed in Japan

IMPORTANT

INFORMATION
CAUTION
TO PREVENT SHOCK,  DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED NEC SERVICE PERSONNEL.  [. . . ] (There is approximately 10. 5° of up and down adjustment for the front of the projector. )

screen

PUSH POWER ON/OFF

STATUS

31 6. To fine tune the image's position vertically on the screen,  rotate each front foot. Increase or reduce the size of the projected image by pressing the "Zoom" (+) or (­) buttons on the remote control or top of the cabinet. 

17

INSTALLATION

32

WARNING
· · · · Only use your LCD projector on a solid,  level surface. If the projector falls to the ground,  you can be injured and the projector severely damaged. Do not use the LCD projector where temperatures vary greatly. The projector must be used at temperatures between 32°F (0°C) and 104°F (40°C). Do not expose the LCD projector to moisture,  dust,  or smoke. This will harm the screen image. 
Screen size = diagonal(inch)

Distance from optical axis center

Ensure that you have adequate ventilation around your LCD projector so heat can dissipate. Do not cover the vents on the bottom or the side of the projector. 

1. 64 ft (0. 5 mm) 0 1. 43 ft (435. 2 mm)

235"-300"

Optical axis center line

165"-222"

115"-150"

77"-100"

47"-60"

20"-27"

Screen center line (Telephoto)

6. 5° 8. 5°

Ceiling Installation
Installing your MultiSync MT1000 LCD Projector on the ceiling must be done by a qualified technician. Contact your NEC dealer for more information. Do not attempt to install the projector yourself. 
NOTE : Distances may vary ± 5%. 

3. 28 ft (1 m) 13. 39 ft (4081. 9 mm)

Screen center line (Wide)
13. 12 ft (4 m) 19. 69 ft (6 m) 26. 25 ft (8 m) 40. 03 ft (12. 2 m) 39. 37 (12) 36. 09 (11) 32. 81 (10) 29. 53 (9) 26. 25 (8) 22. 97 (7) 19. 69 (6) 16. 40 (5) 13. 12 (4) 9. 84 (3) 6. 56 (2)

7. 87 ft (2. 4 m)

13. 12 ft (4 mm)

3. 28 (1)

0 (ft) 0 (m)

Distance from lens surface

33 If your projector is mounted on the ceiling and your image is upside down,  use the "Menu" and "Select" buttons on your projector cabinet or (v) (w) buttons on your remote control to correct the orientation. (See page 60. )

Reflecting The Image
Using a mirror to reflect your LCD projector's image enables you to enjoy a much larger image. Contact your NEC dealer if you need a mirror. If you're using a mirror and your image is inverted,  use the "Menu" and "Select" buttons on your projector cabinet or (v) (w) buttons on your remote control to correct the orientation. (See page 60. )
Mirror

Screen

Rear Screen Projection
You can use your MultiSync MT1000 LCD projector to project an image from the rear onto a transparent screen. The distance the projector must be from the screen is the same as if you were projecting the image from the front. Contact your NEC dealer if you need a transparent screen. If you're projecting the image from the rear and your image is inverted,  use the "Menu" and "Select" buttons on your projector cabinet or (v) (w) buttons on your remote control to correct the image. (See page 60 . )

18

INSTALLATION

34

Wiring Diagram

Document Camera

REMOTE CONTROL INPUT OUTPUT

DC12V/400mA PC CONTROL OUTPUT

VIDEO INPUT AUDIO INPUT L / MONO R

S-VIDEO INPUT

AUDIO OUTPUT

VCR or LaserDisk Player

To video,  S-video,  and audio inputs on the LCD projector. 

L / MONO RGB INPUT 1

R AUDIO RGB MONITOR OUTPUT

RGB INPUT 2

AUDIO

IBM/MAC MultiCable To mini D-Sub 15-pin or D-Sub 15-pin connector on the LCD Projector. 

35 IBM VGA or Compatibles Macintosh or Compatibles

PS/2 mouse adapter (supplied)

Mac ADB adapter (supplied)

Remote Mouse Receiver

Remote Mouse Receiver

Remote Control Guideline 1. Plug the serial cable with the remote mouse receiver into your computer's mouse port and restart your computer to gain remote mouse control. When using the remote control's built-in infrared mouse on a laptop computer,  the laptop's mouse,  trackball or trackpad will be disabled.  [. . . ] Use the menu icons to select your source (Video,  S-Video,  RGB1 or 2). (See pages 51 and 52. ) Ensure your cables are connected properly. Use icons to adjust the brightness and contrast. Reposition the projector to improve its angle to the screen.  [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE NEC MT1000

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual NEC MT1000 will begin.