User manual NEC MT1050

[. . . ] LCD Projector MultiSync MT1055/MT1050/MT850 User's Manual LIMITED WARRANTY (USA and Canada only) NEC SOLUTIONS' PROJECTOR PRODUCTS NEC Solutions (America), Inc. (hereafter NEC Solutions) warrants this product to be free from defects in material and workmanship under the following terms. HOW YOU CAN GET WARRANTY SERVICE 1. To obtain service on your product, consult the dealer from whom you purchased the product. Whenever warranty service is required, the original dated invoice (or a copy) must be presented as proof of warranty coverage. [. . . ] NOTE: Refer to your VCR or laser disc player owner's manual for more information about your equipment's video output requirements. E ­ 23 EN U Y CA NCEL S E LE C T S O U R C M E A U TO A D JU S T AU DIO RG B OU MONIT TPU OR T AU DIO RG B INP AU DIO UT 1 AU DIO RG B INP S-V IDE UT O L/M ON O R 2 RG B OU MON TP ITO UT R VID AC IN AU DIO EO S-V AU RG B IN PU T1 IDE DIO RG B IN O S-V IDE O L /M PU T2 ON O R VID VID EO EO Document camera About Startup screen (Menu Language Select screen) When you first turn on the projector, you will get the Startup screen. This screen gives you the opportunity to select one of the seven menu languages: English, German, French, Itilan, Spanish, Swedish and Japanese. To select a menu language, follow these steps: 1. Use the Select v or w button to select one of the seven languages for the menu. 2. Press the Enter button to execute the selection. The Basic/Custom menu will be displayed in the language you have selected. To close the menu, press the Cancel button. After this has been done, you can proceed to the advanced menu operation. If you want, you can select the menu language later. See "Language" on page E-35. E ­ 24 3. OPERATION This section describes how to select a computer or video source, how to adjust the picture, and how to customize the menu or projector settings. 3. Press the button or the "Enter" button on the projector cabinet or the "Left Click" button on the remote control to select a submenu or item. Adjust the level or turn the selected item on or off by using "Select" or buttons on the cabinet, or the "Mouse button" on the remote control. The on-screen slide bar will show you the amount of increase or decrease. Changes are stored until you adjust it again. ENTER . . . . . . . . . Return to the previous screen without storing settings or adjustments. NOTE: You can close the main and sub menus simultaneously by pressing the PJ button to cancel the Projector mode. General Controls Before you turn on your projector, ensure that the computer or video source is turned on and that your lens cap is removed. 1. Turn on the Projector Plug the supplied power cable in the wall outlet. The projector will go into its standby mode and the power indicator will glow orange. Only after you press the "On" button on the remote control ("ON/ STAND BY" button on the projector cabinet) will the power indicator turn to green and the projector become ready to use. NOTE: To turn the projector on by plugging in the power cable, use the menu and enable the "Auto Start" feature. Select the Computer, Video Source or PC Card Viewer Press a source button on the remote control or the projector cabinet to select "Video" (VCR, document camera, or laser disc player), S-Video", "RGB 1 or 2" (computer or DVD with component output) or "PC Card Viewer" to display the image. Or press the "Menu" button on the remote control or the cabinet and use the menu to select your video source: "Video", "S-Video", "RGB1 or 2", or "PC Card Viewer". Adjust the Image Size and the Focus Use the Zoom ring to adjust the image size, then use the Focus ring to obtain the best focus. Use the "Magnify" button (+) or (-) on the remote control to make the image larger up to 400%. [. . . ] Make sure there are no obstacles between you and the projector. Stand within 22 feet (7 m) of the projector. Make sure that you are in the Projector mode or the PJ button lights in red. If not, press the PJ button. Image is scrolling vertically, horizontally or both Remote control does not work Status indicator is lit or blinking Cross color in RGB mode · See the Power/ Status Light messages above. [. . . ]