User manual NEC MT600

[. . . ] NEC Multimedia Theatre NEC Multimedia Theatre LCD Projector User's Manual R 600 NEC Technologies, Inc. 1250 N. Arlington Heights Road, Suite 500 Itasca, Illinois 60143-1248 Part No. 78406832 Printed in Japan IMPORTANT INFORMATION CAUTION TO PREVENT SHOCK, DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED NEC SERVICE PERSONNEL. Precautions Please read this manual carefully before using your NEC MultiSync MT600 LCD Projector and keep the manual handy for future reference. [. . . ] 47 Getting To Know Your MultiSync MT600 LCD Projector Front Features Built-in speakers (1W Lens with Lens cover Carrying handle 2) Rear Features Lamp cover Remote sensor Remote sensor Lamp cover set screw One Touch Tilt buttons Remote Sensor AC INPUT Connect the supplied power cable' s three-pin plug here. Main POWER switch Ventilation holes(inlet) Feet INTRODUCTION 16 Top Features 1. Power Button Use this button to tu rn the power on and off when Main Power Switch is on and the LCD projector is on standby. (When this button is pressed and held for at least two seconds, the "Display Mute" mode will be canceled. ) 2. Menu Button Displays the icons you need to select a source or adjust your image. Select Button After your press the "Menu" button, use this button to select the menu icon of the item you wish to adjust. (If the icons don't appear after you press the "Menu" button, hold down the "Select" button while using the (+) (-) focus button to adjust the image up or down until the icons do appear. ) 4. Use these buttons to increase or decrease the level of a selected menu item. An on-screen gauge will appear to show you how the level is changing. These buttons also turn a selected menu item on (+) or off (-). Zoom: Hold down the "Zoom" button while you press the (+) button to to make the image larger; or press (-) to make the image smaller. Focus: Hold down the "Select" button while you press the (+) or (-) buttons to focus an image. Power Indicator When this indicator is green, the LCD projector is on; when the indicator is amber, it is standing by. Status Indicator When this is lit red continually , it's warning you that the projection lamp has exceed 2000 hours of service. After this light appears, it is advisable to replace the projection lamp as soon as possible. (See page 41. ) 5. Installer une nouvelle ampoule et fixer le coffret de l'ampoule avec les deux vis. PRECAUTION: Ne pas utiliser d'autres ampoules que l'ampoule NEC en option. Faire la commande avec le numéro de modèle de votre projecteur. Replacer le couvercle de l'ampoule et fixer avec la vis. Après l'installation de la nouvelle ampoule, sélectionner l'ic^ ne de l'usage de o l'ampoule, presser sans relacher le bouton "Power On" sur l' appareil à télécommande pendant 10 seconds afin de remettre l'horloge de l'ampoule a zero. NOTE: Quand vous remplacez l'ampoule, il est recommande de changer aussi le filtre. POWER PUSH ON/OFF MENU 1 2 3 SELECT + STATUS POWER ZO O FO M CU S 4 5 6 17 ATTENTION: Le filtre est inclus dans l'emballage de la nouve PRECAUTION: Ne pas arrêter le projecteur à écran à cristaux liquides (LCD) sauf pour remplacer l'ampoule et/ou le filtre à air. 46 REMPLACER L'AMPOULE Apriès un fonctionnement de 2000 heures ou plus, un signal lumineux s'affichera dans le coffret de l'appareil. M^me si l'ampoule demeure fonctionnelle, e ATTENTION · NE PAS TOUCHER A L'AMPOULE immédiatement après usage. Attendre au moins une heure pour laisser l'ampoule e refroidir av · NE PAS ENLEVER D'AUTRES VIS que la vis fixant le couvercle de l'ampoule et les deux vis du coffret de l'ampoule car cela peut provoquer une électrocution. Pour remplacer l'ampoule: 1. [. . . ] By turning this switch on, the projector will go into its standby mode and the power light will glow amber. Only after you press the "On" button on the remote control or projector cabinet will the power light turn to green and the projector become ready to use. NOTE: To turn the LCD projector on and off with just the back panel switch, use the menu and enable the "auto start" feature. Select The Computer Or Video Source Press the "Video" (VCR or laser disc player), "S-video", or "RGB" (computer or document camera) button on the remote control to display the image. Or press the "Menu" button on the cabinet and use the icons to select your video source: "Video, " "S-Video" or "RGB. " 33 cable to connect to the projector. [. . . ]