User manual NEC MT810[1].PART2

[. . . ] Your serial number is located under the name plate label on the right side of your MultiSync MT830/1030 . Record it here: CAUTION TO PREVENT SHOCK, DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED NEC SERVICE PERSONNEL. This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical shock. [. . . ] The distance the projector must be from the screen is the same as if you were projecting the image from the front. Contact your NEC dealer if you need a transparent screen. If you're projecting the image from the rear and your image is inverted, use the "Menu" and "Select" buttons on your projector cabinet or (v) (w) buttons on your remote control to correct the image. (See page 70 . ) 23 INSTALLATION 44 45 Wiring Diagram To video, S-video, and audio inputs on the LCD Projector. VCR, DVD Player or LaserDisc Player Monitor PC CONTROL MOUSE OUTPUT R GB M ON I TOR OU TP U T L / M ON O R AUDIO REMOTE CONTROL INPUT S ­V I D E O I N P U T AUDIO R GB INPUT 1 AUDIO R GB INPUT 2 AUDIO L / M ON O VIDEO INPUT AUDIO R Remote cable Mouse adapter (For Macintosh) Macintosh or Compatibles (Desk top type) Pin adapter for Macintosh (supplied) Mouse adapter (For IBM PS/2) IBM VGA or Compatibles Document Camera Signal cable (supplied) To mini D-Sub 15-pin connector on the LCD Projector. Remote Control Guideline 1. Plug the serial cable with the mouse output port of the projector into your computer's mouse port and restart your computer to gain remote mouse control. When using the remote control's built-in infrared mouse on a laptop computer, the laptop's mouse, trackball or trackpad will be disabled. Disconnect the serial cable from the mouse output port and restart your computer to regain trackball or trackpad mouse control. If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power management software. If you accidentally hit the OFF button on the remote control, wait one full minute and then press the ON button to resume. 24 INSTALLATION 46 47 Connecting Your PC Or Macintosh Computer Connecting your PC or Macintosh computer to your MultiSync MT830 (SVGA) /1030 (XGA) Projector will enable you to project your computer's screen image for an impressive presentation. All of these following display standards are supported: VGA 640 480 for graphics VGA 640 400 for graphics VGA 640 350 for graphics VGA 720 400 for text VGA 720 350 for text SuperVGA 800 600 Macintosh at 640 480 Macintosh at 832 624 XGA1024 768 Macintosh at 1024 768 SXGA1280 1024 (AccuBlend) To connect to a PC, Macintosh or computer equipped with an XGA/ SVGA /VGA adapter or compatible graphics adapter, simply: 1. Windows 95 There are two methods you can use to change your resolution. Move your cursor to the background image and click. In the "Properties" menu, select "Settings. " 3. Change your resolution and click "OK. " 4. You may be asked to reboot for the changes to take affect, or you' ll get a message that "Windows is about to resize your display. " You' ll be asked if you want to keep your settings. Click on your "My Computer" icon. Open "Control Panel" and select "Display. " 3. Change your resolution and click "OK. " after the new resolution is selected. You may be asked to reboot for the changes to take affect, or you' ll get a message that "Windows is about to resize your display. " You' ll be asked if you want to keep your settings. Click on the "Main" icon and open "Control Panel. " 2. Select "Change System Settings" and click on "Option. " 3. [. . . ] · Use the menu icons to select your source (Video, S-Video, RGB1, 2 or PC Card). (See pages 61 and 62. ) · Ensure your cables are connected properly. · Use icons to adjust the brightness and contrast. · Reset the settings or adjustments to factory preset levels using the RESET icon on the Settings Menu. [. . . ]