User manual NEC MT830

[. . . ] MT830+TM/MT1030+TM/MT1035+TM MultiSync NEC Multimedia Theatre NEC Multimedia Theatre NEC Technologies, Inc. Arlington Heights Road, Suite 500 Itasca, Illinois 60143-1248 Part No. 78410751 Printed in Japan LCD Projector User's Manual NEC Technologies ® IMPORTANT INFORMATION CAUTION To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. 1 Precautions Please read this manual carefully before using your NEC MultiSync MT830+/MT1030+/MT1035+ LCD Projector and keep the manual handy for future reference. [. . . ] Disconnect the serial cable from the mouse output port and restart your computer to regain trackball or trackpad mouse control. If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power management software. If you accidentally hit the OFF button on the remote control, wait one full minute before turning the projector on again. 26 INSTALLATION 50 51 Connecting Your PC Or Macintosh Computer Connecting your PC or Macintosh computer to your MultiSync MT830+ (SVGA) /MT1030+ and MT1035+ (XGA) Projector will enable you to project your computer's screen image for an impressive presentation. All of these following display standards are supported: VGA 640 480 for graphics VGA 640 400 for graphics VGA 640 350 for graphics VGA 720 400 for text VGA 720 350 for text SuperVGA 800 600 Macintosh at 640 480 Macintosh at 832 624 XGA1024 768 Macintosh at 1024 768 SXGA1280 1024 (AccuBlend) To connect to a PC, Macintosh or computer equipped with an XGA/ SVGA /VGA adapter or compatible graphics adapter, simply: 1. Turn off the power to your projector and computer. If your PC does not support XGA/SVGA/VGA you will need to install an XGA/SVGA/VGA graphics board. Consult your computer's owner's manual for your XGA/SVGA/VGA configuration. If you need to install a new board, see the manual that comes with your new graphics board for installation instructions. 3. Use the signal cable that's supplied to connect your PC or Macintosh computer to the projector. For a Macintosh, use the supplied pin adapter to connect to your Mac's video port. If the projector goes blank after a period of inactivity, it may be caused by a screen saver installed on the computer you've connected to the projector. When using a Macintosh with the MT830+/MT1030+/MT1035+, set the DIP switches of the supplied pin adapter according to your resolution. See the following pages for setting of the DIP switches. · When using with a Macintosh, XGA/VGA/SVGA is recommended if your Macintosh supports this mode. · When using with a Macintosh PowerBook, output may not be set to 1024 768 unless "mirroring" is off on your PowerBook. Refer to owner's manual supplied with your Macintosh computer for mirroring. NOTE: A Video Adapter cable manufactured by Apple Computer is needed for a PowerBook which does not have a mini D-Sub 15pin connector. Settings for Monitor Mode Number of DIP switch S1 S2 S3 S4 S5 S6 S7 S8 Monitor size 15" multi-scan mode /16"­13" 17" multi-scan mode /19"­13" 19" multi-scan mode /21"­13" 13" fixed mode /640 480 VGA/SVGA mode 16" fixed mode /832 624 19" fixed mode /1024 768 ON ON ON ON ON ON ON ON ON ON NOTE: For settings other than display modes supported by your Macintosh and MT830+/MT1030+/MT1035+, use of the DIP switch may bounce a image slightly or may display nothing. If this happens, set the DIP switch to the 13" fixed mode and then restart your Macintosh. After that, restore to a displayable mode and then restart the Macintosh again. Make sure that the MT830+/MT1030+/MT1035+ and your Macintosh are connected with the pin adapter and the supplied signal cable (mini D-Sub 15-pin connector) and then restart your Macintosh. 27 INSTALLATION 52 53 Examples of DIP switch setting 13" fixed mode ON ON 17" multi-scan mode ON VGA/SVGA mode 12345678 12345678 12345678 NOTE: Refer to your computer's owner's manual for more information about your computer's video output requirements and any special identification or configuring your projector's image and monitor may require. Settings for Macintosh Adapter Macintosh models applied Setting Mode (Fixed resolution) Setting required to be selected resolution on Mac after restarting. 624) Set to VGA/SVGA (800 600) Desktop type and PowerBook with 16" fixed mode (output is 832 800 600 LCD panel PowerBook with 640 480 LCD panel Desktop type with AccuBlend 13" fixed mode (output is 640 19" fixed mode (output is 1024 480) 768) Set to 17" multi-scan mode (640 Set to 17" multi-scan mode (1024 480) 768) 28 INSTALLATION 54 55 Changing Video Resolutions Depending on your computer's graphic capability, you may be able to select one of several resolutions. Generally a computer- either a PC or Macintosh- with 1 meg. [. . . ] · Reposition the projector to improve its angle to the screen. · Use the keystone icon or the keystone button to correct the keystone distortion. (See page 20 or 29. ) · Reposition the projector to improve its angle to the screen. · Ensure that the distance between the projector and screen is within the adjustment range of the lens. [. . . ]