User manual NEC MULTISYNC LCD1280

[. . . ] 13" True Color TFT LCD Monitor LCD1280 10/29/99 9:25 AM Page 1 13" True Color TFT LCD Monitor User's Manual NEC Technologies, Inc. Michael Drive Wood Dale, Illinois 60191-1094 Part No. Printed in U. S. A. LCD1280 10/29/99 9:25 AM Page 2 Information for LCD1280 WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY INSERTED. [. . . ] To attach the monitor to your system, follow these instructions: Connection to Graphics Cards using BNC cables The NEC LCD1280 color monitor complements a host of computing platforms. However, because the LCD1280 is a high resolution, full color analog monitor, it may require the use of a graphics card (sometimes referred to as a video card, video adapter or graphics board) that supports high resolution graphics (1280 x 1024), 24-bit color (16. 7M colors), delivers an analog output, and which has 5 1. Turn off the power to the monitor and computer. If necessary, install the graphics card and drivers. Determine the pixel frequency (DOT clock) output and the SYNC method used by the graphics card or system. For more information, refer to the graphics card or system manual or the FastFacts document referred to above. Make sure the H-SEL switch on the rear of the panel is positioned to the appropriate pixel frequency (if you are not sure, refer to the board manual or documents). Under most cases, a timing of 107. 5 MHz will apply (Mode 1). For SGI's INDIGO2, a timing of 107. 352 MHz applies (Mode 2). 1 2 H-SEL Pixel Frequency (DOT clock): H-SEL Mode 1 -- 107. 5 MHz H-SEL Mode 2 --- 107. 352 MHz 4. Make sure the SYNC switch on the rear of the panel is positioned to the appropriate mode. SYNC Input Mode: OFF -- Separate Sync/ Composite Sync ON -- Sync on Green OFF ON LCD1280 10/29/99 9:25 AM Page 6 Installation 5. Make sure the appropriate BNC cable is used. When the power is on, the LED is lit. Rear Controls: Display Position / Clock Delay Adjust H-SEL Pixel Frequency Select 0 E C A 8 Sync Mode Select H-C H-V2 H-H2 H-H1 H-V1 V-H2 V-V2 V-C V-V1 V-H1 2 4 6 OFF SYNC ON H/CS VS R G/SYNC B SYNC Mode Select Switch: allows selection between Standard mode (OFF) and Sync on Green (ON) priority mode. H-SEL Pixel Frequency Select Switch: selects the external pixel clock source for WS timing 1 (107. 5 MHz) or WS timing 2 (107. 352 MHz). WS Clock Delay Adjust (H-C): adjustment of WS pixel clock delay rate. Rough WS Horizontal Adjust (H-H1): rough adjustment for horizontal position of WS mode (16 dot increment per operation). Fine WS Horizontal Adjust (H-H2): fine adjustment for horizontal position of WS mode (1 dot increment per operation). Rough WS Vertical Adjust (H-V1): rough adjustment for vertical position of WS mode (16 line increment per operation). Fine WS Vertical Adjust (H-V2): fine adjustment for vertical position of WS mode (1 line increment per operation). VGA Clock Delay Adjust (V-C): adjustment of VGA pixel clock delay rate. Rough VGA Horizontal Adjust (V-H1): rough adjustment for horizontal position of VGA mode (32 pixel / 16 dot increment per operation). [. . . ] Any shipment of the Product (claims must be presented to the carrier). Any other cause which does not relate to a Product defect. Cartons, carrying cases, batteries, external cabinets, magnetic tapes, or any accessories used in connection with the product. What NECTECH Will Pay For and What We Will Not Pay For NECTECH will pay labor and material expenses for covered items, but we will not pay for the following: 1. Costs of initial technical adjustments (set-up), including adjustment of user controls. [. . . ]