User manual NEC PG9000

[. . . ] INTRODUCTION Before operating this projector, please read this manual carefully and completely. This manual will provide you with the basic instructions for operation of the projector. Installation, preliminary adjustments and procedures which require the opening of the projector and contact with electrical components should be performed by service personnel. For continued safe and reliable operation, use only cables supplied by the manufacturer for power. [. . . ] When pressed once, the confirmation message will be displayed. When "YES" is selected and ENTER is pressed, the data will be returned to the standard level. Pressing with CTL returns the adjustment data to the last stored level (LOAD function). 25. PIN CUSHION CONV Button Press to enter the PIN-CUSHION CONVERGENCE mode. You can adjust the horizontal and the vertical pin-cushion convergence for the red or blue CRT. Pressing with CTL button controls the PINBALANCE convergence. 35. · When not using the remote for a long period, remove the batteries. · Do not use new and old batteries together, or use different types together. · Do not take apart the batteries, heat them, or throw them into a fire. · Avoid using the full function remote control as wireless with the backlight switch ON for an extended period of time. This can cause short battery life. 9 BASIC OPERATION Projecting the Picture To project the picture source, proceed as follows: 1) Turn on the main power of the projector. · Press the POWER switch on the front terminal. 2) Turn on the connected equipment's power. · Press the POWER ON button on the remote control or the POWER button on the rear panel. 4) Select an input signal source by pressing one of the ten INPUT buttons on the remote control. You can also select a signal from the "INPUT SELECT" list. · See page 20 "INPUT SELECTION" for more details. · See pages 14 through 18 for more details. NOTE: The volume function works only with the ISS-6010/ISS-6010G. 6) To turn off the power, press the POWER OFF button on the remote control or the POWER button on the rear panel. 7) Press the POWER switch on the front terminal to turn off the main power of the projector. 8) Last, turn off the connected equipment power. 10 BASIC OPERATION Displaying the Menu and Adjustment Screen You can easily access your desired screen by selecting menus. [. . . ] · A confirmation message will be displayed. Use the CURSOR t or u button to select "YES". Press the ENTER button · The LOAD function will be executed. NOTE: If you select "NO", you will exit this mode suspending current status. XXXXXXXX = Adjustment item to be normalized XXXXXXXX DATA NORMALIZE? YES NO XXXXXXXX DATA LOAD? YES NO XXXXXXXX = Adjustment item to be loaded 22 SPECIFICATIONS Projection type Projection system Scanning frequency Retrace time Video bandwidth CRT Lens Picture size Resolution Pixel resolution Light output Contrast ratio High voltage Input : Refraction type Projector and screen are separated : 3 lens and 3 CRT's in-line H 15 to 61. 1kHz / V 38 to 150Hz (PG-6000/PG-6000G) H 15 to 90kHz / V 38 to 150Hz (PG-9000/PG-9000G) : H 4. 0 µS (fH 15 to 30kH2) H 2. 5 µS (fH 30 to 9OkHz) v 350 µS : 70MHz (-3dB) : 7 inch liquid cooling Deflection angle 90 degrees : Hybrid lenses multilayer coating F1. 0 : 60 to 300 inches diagonal : 1000TV lines : 1280 × 1024 dots : 800 lumens (Small area peak high light brightness) : 1 : 20(HDTV method) : 32kV : RGB signal 0. 7Vp-p 75ohm positive (BNC) H/V sync 0. 7 to 4. 0Vp-p 75ohm negative or positive (BNC) COMP sync 0. 7 to 4. 0Vp-p 75ohm negative o r positive (BNC) Sync on G 0. 3 to 0. 6Vp-p 75ohm negative (BNC) Video 1. 0Vp-p 75ohm positive (BNC) or (switchable) S-video; Y I . 0Vp-p 75ohm positive C 0. 28Vp-p 75ohm (burst level) Video system NTSC, PAL, SECAM and NTSC4. 43 : Digital convergence (Pre-set 100 positions) Quick copy convergence Static and wave convergence Point convergence: PG6000/PG-6000G Optional PG-9000/PG-9000G Standard : Less than 0. 2% of V-height : 20 minutes : Cross hairs, Cross hatch. [. . . ]