User manual NEC PLASMASYNC 61XM4(MM)

[. . . ] The plasma display panel consists of fine picture elements (cells). Although NEC produces the plasma display panels with more than 99. 99 percent active cells, there may be some cells that do not produce light or remain lit. For operating safety and to avoid damage to the unit, read carefully and observe the following instructions. Provide adequate space for ventilation to avoid internal heat build-up. [. . . ] Press during display of the sub menu (setting/adjustment screen) to select setting items and also to increase the adjustment value. POSITION/CONTROL RP-102 NOTE: CONFIG MENU Among the various on-screen menus (OSM), only the CONFIG MENU is displayed by pressing and holding the main unit POSITION/CONTROL L button and the PROCEED button simultaneously for 3 seconds or longer. The menu screen of the CONFIG MENU does not contain icons that indicate menu items; however, operation is the same as with other screens. Operation of the Menu Screen Main menu The main menu comprises 2 pages (screens). Place the cursor on icon or and use the POSITION/CONTROL / button to change the page. (Set [OSD MODE] to [PRO] on the configuration menu before performing other operations. ) G Items of the main menu are displayed as icons. See Pages 23 and 24 for details. Sub menu BRIGHTNESS CONTRAST SHARPNESS COLOR TINT G Cursor VOLUME BALANCE MUTE INPUT1 INPUT2 G Indication of the adjustment value. : OFF : VIDEO : RGB1 G Displays the next page. G Place the cursor here and press the button to display the next page. G Items of the main menu are displayed as icons. See Pages 23 and 24 for details. SOURCE INFO. V-POL. 31. 5kHz 60. 0Hz NEG POS G Displays the previous page. NOTE: Auto Memory The setting value is automatically stored after the adjustment. Note that setting values will not be automatically stored in the following circumstances. * The power cable is disconnected from the outlet during the setting. * There is a power outage during the setting. PLASMA MONITOR 25 Configuration Menu (CONFIG MENU) This menu sets the main menu, display of adjustment details, remote control, sync, and the brightness of the multiple system. Preparation Simultaneously press and hold the POSITION/CONTROL L button and the PROCEED button for 3 seconds or longer to display the menu screen. 1 Align the cursor with the desired item CONFIG MENU OSD DISPLAY :NORMAL OSD MODE :BASIC WIRELESS REMOTE CONTROL :ON SYNC MODE :AUTO PLE LINK :OFF ALL RESET Adjustment Items I OSD DISPLAY [NORMAL] : Displays the menu screen and adjustment details. [KEY] : Displays the adjustment details for only input switching and direct adjustments. When adjustment is required, set [AUTO PICTURE] to [OFF]. When the displayed image is small with respect to the original number of horizontal pixels (including instances where the display area, i. e. , lit pixels is small), the picture may take up to 6 seconds to be displayed. I RGB MODE [MOTION] : Set when a moving picture source is connected such as a scan converter. [STILL] : Set when displaying a personal computer screen. [DTV] : Set when viewing a source such as a digital broadcast using RGB input. I Clock Frequency Adjustment (PICTURE ADJ) This adjusts the width of the image with respect to the screen. Adjustment is performed with a dot unit signal. Adjust to the position at which vertical flickering disappears. 3 Select OFF with the POSITION/CONTROL buttons AUTO PICTURE : OFF INPUT MODE : 4X3 RGB MODE : STILL PICTURE ADJ FINE PICTURE WIDE MODE : FULL 4 Align the cursor with the desired item Move the cursor up and down with the POSITION/CONTROL LM buttons. AUTO PICTURE : OFF INPUT MODE : 4X3 RGB MODE : STILL PICTURE ADJ FINE PICTURE WIDE MODE : FULL When the width of the image signal is wider than the monitor screen, adjust the size with the POSITION/ CONTROL button. When the width of the image signal is narrower than the monitor screen, adjust the size with the POSITION/ CONTROL button. : Monitor screen size : Image signal size I Clock Phase Adjustment (FINE PICTURE) Adjust for minimal screen noise, flicker, and color infidelity. First adjust the clock frequency, then perform the clock phase adjustment. * Clock frequency and clock phase adjustments are not available at the time of VIDEO (and S-VIDEO) input. INPUT MODE: [4x3], [16x9] and [16x9!] are used in the discrimination and switching of the input signal. See "INPUT MODE" of "Signal Identification For Raster Preset" (P. 64) when making the setting. PLASMA MONITOR 29 Auto Picture/Wide Screen Settings (AUTO PICTURE) Wide Screen Setting (WIDE MODE) This sets the wide screen display (to NORMAL, FULL, ZOOM, or STADIUM). Preparation Press the PROCEED button to display the main menu. 1 Align the cursor with Important I Precautions in Normal Mode There are marked differences in brightness between the display portions and non-display portions (where there is no image) in [NORMAL] mode which result in image burn-in due to the strong contrast. [. . . ] · Has an ID number been set for the main unit?· Are the remote control's batteries worn out?· Is the remote control pointed at the monitor, or is there an obstacle between the remote control and the monitor?· Is direct sunlight or strong artificial light shining on the monitor's remote control sensor? Monitor does not operate when the remote control's buttons are pressed. · You are not within the effective operating range. (Wireless) · Has an ID number been set for the main unit? [. . . ]