User manual NEC REMOTE MT40

[. . . ] Use the vw buttons to select the submenus or adjustment or setting items. See below for a list of the remote control unit buttons that can be used while the menu is displayed and the functions of the menus and dialog box elements. vw buttons sbutton tbutton : Used to select items on menus or elements in dialog boxes. : Activates submenus or executes the selected item. [. . . ] If you wish to store the correction setting so that it is still set when the power is turned back on next time, do so under "Projector Options" a "Setup" a "Page 2" a "Keystone Save". Factory Default Use the ts buttons to select "All Data" or "Current Signal", press the Down button, highlight the "OK" button, then press the ENTER button. The settings and adjustments are restored to the factory settings. Image Options Menu Use vw to select "Image Mode" or "Video Mode", then press the s or ENTER button. Image Mode Adjust the aspect ratio according to the signal to be projected. Use the vw buttons to select "Aspect", then use the ts buttons to select the corresponding radio button. Aspect Normal Zoom : 4:3 images are displayed with a 4:3 ratio. : 16:9 images are expanded in the vertical and horizontal directions and displayed with a 4:3 ratio. Wide Zoom : 16:9 squeeze images are displayed with a 4:3 ratio in the horizontal direction. Cinema : The vertical amplitude of 16:9 squeeze images is reduced and the images are displayed with a 16:9 ratio. Video Mode Select Gamma, Noise Reduction and Color Matrix according to the signal to be projected. For Gamma and Color Matrix, use the ts buttons to select the desired radio button. For Noise Reduction press the s button to display the pull-down menu, then use the vw button to select the level. Gamma Correction Normal : Default for RGB signal Natural 1 : Default for Video and S-Video signal Natural 2 : Default for component signal Noise Reduction Select the level (Off, Low, Medium or High). Color Matrix Select Color Matrix HDTV : High Definition TV signals SDTV : Standard Digital TV signals Select Color Matrix Type Select the appropriate type (B-Y/R-Y, Cb/Cr or Pb/Pr). Projector Options Menu Set the menus and various items. Set the menu language, pointer shape, whether or not to display items, the type of projector, etc. Use vw to select the item then press s or the ENTER button. Menu Use the v, w, t, s buttons to select the item (Language, Projector Pointer, or Source Display). When Source Display is set to "Off", the selected items are displayed on the screen only when the power is turned on and when the input is switched. Use the vw buttons to select the menu language. Use the vw buttons to select one of the 8 types of pointer icons. Setup Make the various settings according to how the projector is to be used. The OK and Cancel buttons affects all four pages. Note that the LT series projectors have three pages. next page Page 1 Orientation Set the projection method. Use the vw buttons to select Front Floor, Rear Ceiling, Rear Floor or Front Ceiling. Background Select the background when there is no signal. Use the vw buttons to select Blue, Black, or Logo. Signal Select RGB:Normally select "Auto". RGB and component signals are switched automatically. If the signal does not switch when component signals are input, select the "Component". When "Auto" is selected, NTSC 3. 58, NTSC 4. 43, PAL, PAL 60 or SECAM is selected automatically. (NTSC 4. 43 and PAL 60 are not identified automatically when the LT series projector is used. To view in one of these modes, select the mode from the pull-down menu. ) previous page next page Page 2 Mouse Buttons Use the Left and Right buttons to set the mouse button mode to "Righthanded" or "Left-handed". Speed Set the mouse speed to High, Medium or Low. Auto Start When this is selected, the projector turns on automatically when the power cord is plugged into an outlet. Power Management When this is selected, the standby mode is set automatically if no signal is input for 5 minutes. Power Off Confirmation When this is selected, a verification message is displayed when turning the power off. Keystone Save When this is selected, the setting for compensating for trapezoidal distortion is stored and remains in the memory even when the power is turned off. [. . . ] With the full function remote control unit, when this button is pressed the COMPUTER/PJ SELECT button automatically lights red and the mouse buttons are set to the projector mode. PICTURE MUTE button Press this to mute the image and sound. Press again to cancel the mute mode. HELP button Press this when nothing is selected to display the help menu. When pressed while the help menu is displayed, the description of the help function is displayed. When press while menus or adjustment/setting screens are displayed, help on that subject is displayed. [. . . ]