User manual NEC VERSA 4000

[. . . ] PROPRIETARY NOTICE AND LIABILITY DISCLAIMER. The information disclosed in this document, including all designs and related materials, is the valuable property of NEC Corporation (NEC) and/or its licensors. NEC and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights to this document, including all design, manufacturing, reproduction, use and sales rights thereto, except to the extent said rights are expressly granted to others. The NEC product(s) discussed in this document are warranted in accordance with the terms of the Warranty Statement accompanying each product. However, actual performance of each such product is dependent upon factors such as system configuration, customer data, and operator control. [. . . ] Prepare your option for installation as follows: s To install a battery pack, first connect it to the bay adapter that came with the battery. (Follow the instructions that came with the battery pack. ) s To install a hard disk drive, first connect it to the ap- propriate bay adapter or drive cradle pak. (Follow the instructions that come with the adapter or cradle pak. ) 8. Align the option and its carrier in the VersaBay II and push it in until the option clicks into place. 9. The system should automatically recognize the newly installed option. Using the Hardware 2-21 External Monitor You can add a standard external monitor to your NEC Versa 4000. You need a display signal cable (usually provided with the monitor). One end of the cable must have a 15-pin connector for the system. Follow these steps to connect an external monitor to your NEC Versa 4000. 1. Check that the NEC Versa is in Suspend mode or pow- ered off and the monitor power switch is turned off. The NEC Versa must be in Suspend mode or powered off while the monitor is being connected. NOTE 2. Open the port cover on the back of the system. Attach the 15-pin cable connector to the monitor port on the system. Secure the cable connection with the screws provided. Monitor Port Connecting a monitor 2-22 Using the Hardware 4. Connect the monitor power cable and plug it into a properly grounded wall outlet. 5. Follow any setup instructions in the monitor manual. Press the Suspend button to resume Active mode or power on the NEC Versa 4000. Press the Fn + F3 function key combination to toggle between the LCD, CRT, or simultaneous display on both. Printer You can attach a printer with either a parallel or a serial connector. A parallel printer connector has 25 pins; a serial connector has 9 pins. Some printers come with both types of connectors. Parallel Devices To install a parallel device, such as a printer, you need a cable with a male 25-pin connector for the system and, for most parallel printers, a Centronics®-compatible 36-pin connector. When you connect a printer, be sure to install the appropriate printer driver through the Windows Control Panel. NOTE Connect a parallel device to your NEC Versa 4000 as follows. 1. Check that both the NEC Versa and parallel device power are off. Using the Hardware 2-23 2. Open the port cover on the back of the system and locate the parallel port. 3. Align and connect the 25-pin parallel cable connector to the parallel port on the system. Secure the cable with the screws provided. 4. [. . . ] During these breaks, stretch muscles and joints that were in one position for an extended period of time. Relax muscles and joints that were active. s Use a timer or reminder software to remind you to take breaks. s To enhance blood circulation, alter your sitting posture periodically and keep your hands and wrists warm. For more information on workstation setup, see the American National Standard for Human Factors Engineering of Visual Display Terminal Workstations. Box 1369, Santa Monica, California 90406 NOTE A-6 Setting Up a Healthy Work Environment PRE-EXISTING CONDITIONS AND PSYCHOSOCIAL FACTORS Pre-existing conditions that may cause or make some people more susceptible to musculoskeletal disorders include the following: hereditary factors, vascular disorders, obesity, nutritional deficiencies (e. g. , Vitamin B deficiency), endocrine disorders (e. g. , diabetes), hormonal imbalances, connective tissue disorders (e. g. , arthritis), prior trauma (to the hands, wrists, arms, shoulders, neck, back, or legs), prior musculoskeletal disorders, aging, fluid retention due to pregnancy, poor physical conditioning and dietary habits, and other conditions. Psychosocial factors associated with these disorders include: workplace stress, poor job satisfaction, lack of support by management, and/or lack of control over one's work. [. . . ]