User manual NEC VT65 QUICK GUIDE

[. . . ] See page E-14. -CO OU NT RO BO IN Infrared T ransmitter Direct the remote control toward the remote sensor on the projector cabinet. Power ON Button If the main power is applied, you can use this button to turn your projector on. Power OFF Button If the main power is applied, you can use this button to turn your projector off. NOTE: To turn off the projector, press and hold the POWER OFF button for a minimum of two seconds. L S-V EO 2 3 Unavailable items will be skipped. Adjusting the T ilt Foot 1 Press and hold the T ilt button on the front of the Power down all equipment before making connections. projector . O N /O FF 15 7m 2 Lift the front edge of the projector to the desired height, and release the button to lock the able T ilt Foot. 4 RG INP B UT AU D OU TP UT PC -CO NT RO L Aspect Button Press this button to display the Aspect Ratio select window. [. . . ] Picture Mute Button This button turns off the image and sound for a short period of time. Press again to restore the image and sound. Magnify Button Use this button to adjust the image size up to 400%. V olume Button Press (+) to increase the volume and (­) to decrease it. LE C T EL S O U R C E M E A U TO A D JU S T Monitor PC -CO RG INP B UT AU OU D TP UT IN OU T NT RO L S-V IDE O VID 7 8 O N /O FF ENTER S TA P TU O WS E R P O W S E TA R TU S O CA NC EL S E LE C T Step 2 S O U R C E Connect the supplied power cable. M E NU 9 NU ENTER N /S TA N D B Y CA NC EL S E LE C T U R S O M E C E A U TO A D JU S T RG INP B UT AU D OU TP UT PC -CO NT RO L IN OU T S-V IDE O VID 10 · If the projected image does not appear square to the screen then use keystone correction for proper adjustment. Printed in China 7N8P1131 NOTE: The default is the Computer mode, which allows you to use the Select, Cancel, and Enter buttons as your computer mouse. When the POWER ON/OFF, MENU, HELP or MAGNIFY button is pressed, the PJ button lights red to indicate that you are in the Projector mode. If no buttons are pressed within 10 seconds, the light goes out and the Projector mode is canceled. Basic Menu Source Select RGB Video S-Video Troubleshooting Power/ Status Light Messages Condition Standby Cooling down Lamp in Nomal mode Lamp in Eco mode One minute after lamp is turned on Retrying to turn on lamp Lamp has reached its end of life (2000 hours or over : Normal mode) (3000 hours or over : Eco mode) Lamp life has reached its end of life (2100 hours or over : Normal mode) (3100 hours or over : Eco mode) Lamp or filter cover error (3 locations) Temperature error Fan error Lamp error Common Problems & Solutions Power Indicator Steady orange Blinking green Steady green Steady green Blinking green Steady green Steady green Status Indicator ­ ­ ­ Steady green Depending Lamp mode Blinking orange Steady red Note ­ Blinks green for 60 seconds. ­ ­ Do not turn off the projector during this condition. The projector retries 3 times at an interval of 15 sec for max. Message appears on screen during this condition. Please replace the lamp as soon as possible. The projector is in standby mode and cannot be turned on. The projector is in standby mode and cannot be turned on. The projector is in standby mode and cannot be turned on. The projector is in standby mode and cannot be turned on. The projector is in standby mode and cannot be turned on. Problem Does not turn on Check These Items · Check that the power cable is plugged in and that the power button on the projector cabinet or the remote control is on. · Ensure that the lamp cover is installed correctly. · Check to see if the projector has overheated or the lamp usage exceeds 2100 hours (3100 hours in Eco mode). If there is insufficient ventilation around the projector or if the room where you're presenting is particularly warm, move the projector to a cooler location. [. . . ] Make sure there are no obstacles between you and the projector. Stand within 22 feet (7 m) of the projector. Make sure that you are in the Projector mode or the PJ button lights in red. [. . . ]