User manual NEC VT660K

[. . . ] Portable Projector VT660K/VT460K VT560 User's Manual Important Information Safety Cautions Precautions Please read this manual carefully before using your NEC VT660K/ VT460K/VT560 Projector and keep the manual handy for future reference. Your serial number is located on the bottom of your projector. Record it here: CAUTION To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. [. . . ] Use a 15-pin cable to connect your monitor to the RGB OUT (Mini DSub 15 pin) connector on your projector. Turn on the projector, monitor and the computer. NOTE: · The RGB OUT connector outputs RGB signal during standby mode. When the projector goes into standby mode, the image on an external monitor disappears for a moment. · When the projector is in the standby mode, the image may not be correctly displayed while the cooling fans are running immediately after turning on or off the power. · Daisy chain connection is not possible. E-14 Connecting Your DVD Player RGB IN Optional 15-pin-to-RCA (female) 3 cable (ADP-CV1) Component video RCA 3 cable (not supplied) Audio Equipment DVD player AUDIO IN L R AUDIO OUT L R Component Y Cb Cr Audio cable (not supplied) You can connect your projector to a DVD player with component output or Video output. To do so, simply: For a DVD player without component video (Y, Cb, Cr) output, use common RCA cables (not provided) to connect a composite VIDEO output of the DVD player to the Video Input of the projector. NOTE: Refer to your DVD player's owner's manual for more information about your DVD player's video output requirements. 1. Turn off the power to your projector and DVD player. If your DVD player has the component video (Y, Cb, Cr) output, use a commercially available component video cable (RCA 3) and the optional 15-pin-to-RCA (female) 3 cable to connect your DVD player to the RGB IN connector on the projector. E-15 Connecting Your VCR or Laser Disc Player Video cable (not supplied) S-Video cable (not supplied) Audio equipment VCR/ Laser disc player AUDIO IN AUDIO OUT L R L R S-VIDEO OUT VIDEO OUT Audio cable (not supplied) Use common RCA cables (not provided) to connect your VCR, laser disc player or document camera to your projector. To make these connections, simply: NOTE: Refer to your VCR or laser disc player owner's manual for more information about your equipment's video output requirements. NOTE: An image may not be displayed correctly when a Video or S-Video source is played back in fast-forward or fast-rewind via a scan converter. 1. Turn off the power to the projector and VCR, laser disc player or document camera. Connect one end of your RCA cable to the video output connector on the back of your VCR or laser disc player, connect the other end to the Video input on your projector. Use an audio cable (not supplied) to connect the audio from your VCR or laser disc player to your audio equipment (if your VCR or laser disc player has this capability). Be careful to keep your right and left channel connections correct for stereo sound. Turn on the projector and the VCR or laser disc player. Connecting the Supplied Power Cable Connect the supplied power cable to the projector. First connect the supplied power cable's two-pin plug to the AC IN of the projector, and then connect the other plug of the supplied power cable in the wall outlet. E-16 PROJECTING AN IMAGE (BASIC OPERATION) This section describes how to turn on the projector and to project a picture onto the screen. 2. Press the ENTER button to execute the selection. Turning on the Projector NOTE: · The projector has two power switches: main power switch and POWER (ON/ STAND BY) button (POWER ON and OFF on the remote control). · When plugging in or unplugging the supplied power cable, make sure that the main power switch is pushed to the off (O) position. Failure to do so may cause damage to the projector. To turn on the main power to the projector, press the Main Power switch to the on position ( I ). After this has been done, you can proceed to the menu operation. If you want, you can select the menu language later. [. . . ] Service Options: There are 3 types of "Service" available. Enduser has to understand following condition and is required to fill in the Application Sheet. 1) Repair and Return: The 'Faulty unit' is sent or collected from the customer. It is repaired and returned within 10 days to the customer, excluding transport time. [. . . ]