User manual NEC XT5000

[. . . ] MultiSync XT5000 High Light Output Projection System User's Manual CAUTION: To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. GSGV Acoustic Noise Information Ordinance: The sound pressure level is less than 70 dB(A) according to ISO 3744 or ISO 7779. Precautions Please read this manual carefully before using your NEC MultiSync XT5000 Projector and keep the manual handy for future reference. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. [. . . ] While projecting an image with lower resolution than the projector's native resolution (1024 768), if you want to enlarge the image to fill the screen in the Native mode, proceed as follows: 1. Tturn on the "Native with Zoom" on the Resolution window. While pressing and holding CTL, press MAGNIFY or FOCUS on the remote control to zoom the lens in or adjust the lens focus. Screen Width (H) For TL-08SF 0. 08H 0. 08H Unit: m (feet) Normal Projection Position Screen Width (H) Model Lens Magnification 80" Screen Size (Diagonal) / Projection Distance 100" 200" 300" 400" 500" TL-08SF 0. 84 1. 4 (4. 48) 1. 7 (5. 60) 3. 4 (11. 20) 5. 1 (16. 80) 6. 8 (22. 40) 8. 5 (28. 00) TL-1Z 1. 5-2. 5 2. 5-4. 0 (8. 00-13. 33) 3. 1-5. 0 (10. 00-16. 66) 6. 1-10. 1 (20. 00-33. 33) 9. 2-15. 2 (30. 00-50. 00) 12. 2-20. 3 (40. 00-66. 66) 15. 2-25. 4 (50. 00-83. 33) TL-4Z TL-2Z 4. 0-7. 0 2. 5-4. 0 6. 6-11. 3 4. 1-6. 5 (13. 34-21. 33) (21. 34-37. 33) 8. 2-14. 2 5. 1-8. 1 (16. 67-26. 66) (26. 67-46. 66) 16. 3-28. 4 10. 2-16. 2 (33. 34-53. 33) (53. 34-93. 33) 24. 4-42. 6 15. 3-24. 3 (50. 00-80. 00) (80. 00-140. 00) 32. 6-56. 8 20. 4-35. 5 (66. 67-106. 66) (106. 67-186. 66) 40. 7-71. 1 25. 4-40. 6 (83. 34-133. 33) (133. 34-233. 33) Unit: m (feet) Screen Size 80" 100" 150" 200" 300" 400" 500" H 1. 6(5. 33) 2. 0(6. 67) 3. 0(10. 00) 4. 0(13. 33) 6. 1(20. 00) 8. 1(26. 67) 10. 2(33. 33) V 1. 2(4. 00) 1. 5(5. 00) 2. 3(7. 50) 3. 0(10. 00) 4. 6(15. 00) 6. 1(20. 00) 7. 6(25. 00) * The values for projection distance are estimated. E ­ 18 0. 15V Projection Distance and Screen Size Screen Height (V) 0. 15V 0. 32V Top View Normal projection Reflecting The Image Using a mirror to reflect your projector's image enables you to enjoy a much larger image in a much smaller space. Contact your dealer if you need a mirror. If you're using a mirror and your image is inverted, use the [Main Menu] [Projector Options] [Setup] [Orientation] to select the correct orientation. (See page E-39. ) Rear Screen Projection Lens shifted Screen You can use your XT5000 to project an image from the rear onto a transparent screen. The projection distance is the same for both rear and front projection. Contact your dealer if you need a transparent screen. If you're projecting the image from the rear and your image is inverted, use the [Main Menu] [Projector Options] [Setup] [Orientation] to access to correct the orientation. (See page E-39. ) Side View Lens shifted Screen Stack Projection (up to three units) The MultiSync XT5000 can be stacked without any additional framing (gravity stacking). One unit can be stacked on top of the other up to three units. Make sure that each foot is securely seated on the stacking pad. NOTE: See next page for more details. Normal projection Screen center E ­ 19 Setting up for Double or Triple Stacking in Link Mode INPUT3 RGB INPUT2 R/Cr INPUT1 R/Cr INPUT4 Cr G/Y G/Y Y OPTION IN B/Cb B/Cb Cb OU TP OUT UT Master projector REMOTE1 H/HV H/HV V V OU TP UT INP UT 9 INPUT3 RGB INPUT2 R/Cr INPUT1 R/Cr INPUT4 Cr Slave projector G/Y G/Y Y OPTION IN INP UT B/Cb B/Cb Cb 9 OUT H/HV H/HV REMOTE1 V V OUTPUT RGB DIGITAL INPUT9 OUTPUT INPUT 0 INPUT3 RGB SDI INPUT2 R/Cr INPUT1 R/Cr INPUT4 Cr DFP cable (supplied) OUTPUT RGB DIGITAL SDI G/Y G/Y Y OPTION IN INPUT9 OUTPUT INPUT 0 B/Cb B/Cb Cb OUT H/HV H/HV DFP cable (supplied) OUTPUT RGB DIGITAL SDI INPUT9 OUTPUT INPUT 0 bi-directional RS232C cable (not supplied) REMOTE1 V V NOTE: SW 1 Level and SW 2 Level of Switcher Control are not available on Link Mode. For double or triple stacking, follow the instructions described below. Next, using a commercially available, bi-directional RS-232C cable connect the OPTION OUT terminal of the master projector to the OPTION IN terminal of the slave projector(s) until all the projectors are connected. NOTE: When inputting signals other than those listed on page E44, use a commercially available distribution amplifier between the projector and those signals because those signals are not compatible with this projector in the Digital Link mode. Turn all the projectors on and roughly make some optical adjustments to each projector. 1) Stacking the Projectors 1-1. Place the projectors at the proper height for best screen to projector relationship. Make sure that all projectors have the same display orientation. 2) Hookup 2-1. Use the supplied DFP cable to connect the RGB DIGITAL output (INPUT 9) of the master projector to the RGB DIGITAL input of the slave projector (the second and third stack) until all the projectors are connected. E ­ 20 3) Adjust and register signals to be projected in Link mode and stack application. Signal Data Preparation 3-1. Creating data for the master projector and copying data to the slave projectors. Display all desired input signals, make adjustment to each signal, then save all adjustments on the master projector. [. . . ] When not using Link mode, set to Standalone. See page E-20 for setting up for double or stacking in link mode. E ­ 40 PC Card Files Displaying Current Status of Link Mode When selecting the tab "Page 4 ", you will get the following dialog box. Displays a list of all the files stored in the PC card so that you can select a file you want to display. You can also sort files by file name or date, or display the file. Although a list of all the files in the PC card is displayed, you can view files in text, HTML, JPEG and BMP format only. [. . . ]