User manual NEWPOL XF71207DG

[. . . ] 36 2 IMPORTANT SAFETY INSTRUCTIONS Installation Installation, maintenance and repair work should be by a Miele authorized service technician. Work by unqualified persons could be a hazard and may void the warranty. This equipment is not designed for maritime use or for use in mobile installations such as caravans or aircraft. However, under certain conditions it may be possible for an installation in these applications. [. . . ] Several turns may be needed to set the correct height. Do not use a power screwdriver. ^ Adjust the front leveling legs by pushing on the feet with a slotted screwdriver. ^ Tipping the machine slightly backwards, if posssible will make adjusting the front legs easier. Make sure the machine is level when adjustments are complete. If necessary, individual or all of the filler strips can be removed. Stainless Steel Full size 4 047 341 4 047 361 3 280 742 3 298 210 Slimline 4 312 770 4 312 780 4 316 721 ^ To remove the filler strips from the control panel, place the panel printed side up, and gently push down near the bottom of the control panel. This will release the mounting bolts from their slots. 18 Installation 8. Install the custom door panel A custom door panel matching the kitchen cabinetry can be installed using the provided templates and bracket. As long as the panel length calculated is within the Range of Panel Sizes listed, the custom panel should fit without a problem. Range of Panel Sizes G 636 - G 698 Length: Width: 19" - 23 3/4" (483 - 603 mm) 23 1/2" (598 mm) G 801 - G 832 Length: Width: 21" - 25 3/4" (533 - 654 mm) 17 1/2" (445 mm) G 836 - G 898 Length: Width: X = Panel length A = Height to the underside of the countertop B = Control panel height* C = Toe Kick Height Length X: Determined using the following calculation: X = A ­ B ­ C *Control panel height is determined by the height of the drawers in the cabinets. This height is adjustable between 4 1/2" and 5 3/4" (112 - 145 mm) with the filler strips provided. If the locking screws on the edge of the dishwasher door can not be reached, the dishwasher will have to be pulled out of its opening a few inches. 23 Installation If the adjacent cabinetry (or appliance) does not have drawers and alignment to a drawer line is not possible: ^ Hang the bracket on the machine door, without the templates. Tighten the four locking screws on the edges of the door panel. ^ Measure the distance from the adjacent cabinet's (or appliance) door bottom to the bottom of the mounting bracket (X). ^ Draw a line on the rear of the door panel (X) inches up from the bottom. ^ Remove the bracket from the machine door and place it on the rear of the door panel so that: ­ the bracket is centered left to right, ­ the bottom of the bracket is aligned with the (X) line. ^ Tape the bracket to the door panel to hold it in place while the mounting holes are drilled. ^ Drill pilot holes for the screws using a 3 /32" (2. 5 mm) bit. ^ Attach the bracket to the panel using the 6 screws provided. 24 Installation ^ Push up one side of the door panel until it touches the filler strips (or control panel if filler strips are not being used) and lightly tighten the T20 Torx screws on the corresponding edge of the machine door. Do not use a power screwdriver ^ Repeat the process with the other side of the door panel. ^ Check that the door panel is adjusted correctly. It should be snug at the top and neatly aligned with the adjacent cabinetry. If it is not aligned properly, loosen the Torx screws and readjust the panel Once the door panel is positioned correctly: ^ Open the dishwasher door. [. . . ] An opening through the partition between the compartments of 1 1/2" (3 to 4 cm) can be made to allow the plug to pass through. Permanent Connection (Hard Wiring) For hard wiring, the power cord must be disconnected from the terminal box located at the lower left front of the dishwasher, behind the toekick and service panel. Pass the permanent power supply cable through the strain relief and secure it to the terminal box. Connect: L1 N (Black) to L on terminal block (White) to N on terminal block GRND To ground connector GROUNDING INSTRUCTIONS This appliance must be connected to a grounded metal, permanent wiring system, or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the appliance. Use copper conductors only. , Hardwiring the dishwasher should only be done if required by local electrical codes, and then in accordance with those codes. [. . . ]