User manual NIKE TRIAX SPEED

[. . . ] The completed lap number appears above the primary display. The split time appears for 7 seconds, then the display returns to the overall time. Completed lap time appears for 7 seconds, then the display shows the elapsed time for the next lap. Stop measuring a lap Press the STOP/NEXT button. [. . . ] Press and hold the STOP/NEXT button for two seconds. "HOLD NEXT" flashes in the display. Then the next run sequence appears at the top of the display. Your Triax watch will record the next lap times as part of a new run. EN Manual FINAL (RunII) NEW 4/26/99 5:00 PM Page 8 8 b DATA In DATA mode you can recall lap and split times measurements from your saved runs. RUN NUMBER 9 Reset a run The chronograph must be stopped to reset a run. Press and hold ADJUST/RESET for 2 seconds. "HOLD RESET" flashes to reset current run. Time returns to zero. NOTE: Over 100 hours, the run will be reset automatically. A DJ U S T /R E S E T S TA R T /L A P MODE S TO P /N E XT Switch the primary display between lap and split time In CHRONOGRAPH mode, press the ADJUST/RESET button. Lap and split times will change between primary and secondary position on the display. Note that display settings in CHRONOGRAPH mode are also reflected in DATA mode. D AT E ELECTROLITE Cycle through the run numbers Press the STOP/NEXT button. Run number and date of run are displayed. NOTE: If dashes appear in the display, no data exists for that run. Check remaining memory capacity When the chronograph is reset, press the STOP/NEXT button. Lap memory capacity is displayed. Cycle by date through lap and split times, total time, best time, and average time for each run Press the START/LAP button. EN Manual FINAL (RunII) NEW 4/26/99 5:00 PM Page 10 10 c TIMER TIMER mode provides a programmable countdown interval timer. You can set up to 5 timed segments for your workout. The alarm sounds for fifteen seconds, then pauses for ten. Then it rings for ten seconds, pauses for ten seconds, and rings for ten more seconds. For the last five seconds Nike Electrolite display will flash in unison. AD J U S T/ RE S E T 17 Reset the counter to zero Press and hold ADJUST/RESET for 2 seconds. "HOLD RESET" flashes in the display, then the count returns to zero. S TA RT / LA P M OD E S TO P / N E XT T I M E Z O NE ALARM TIME ON /O F F M A R K E L E C TR O LIT E A L A R M NU M B E R Set an alarm 1 Press the STOP/NEXT button to select one of seven alarms to set. 2 Press and hold the ADJUST/RESET button for 2 seconds. "HOLD ADJUST" flashes in the display, then the hours:minutes and time zone appear. The hours indicator flashes. EN Manual FINAL (RunII) NEW 4/26/99 5:00 PM Page 18 18 19 3 Press the START/LAP button to increase the flashing value. Hold down for quick advance. 7 Press the ADJUST/RESET button to save the changes and activate the alarm. NOTE: Each alarm is active only in the time zone for which it is set. 4 Press the STOP/NEXT button to decrease the flashing value. Advance to the next alarm Press the STOP/NEXT button. The next alarm number appears at the bottom of the display. 5 Press the MODE button to cycle to the next adjustable value. Turn the alarm on and off Press the START/LAP button. The word ON toggles off and on each time you press the button. 6 Repeat steps 3-5 until you have set all values: hour, minutes, time zone. [. . . ] In TIME mode, press and hold the START/LAP and STOP/NEXT buttons simultaneously. While holding buttons, you will hear the sound demonstration. The watch will cycle through the modes, briefly demonstrating the functions of each. Press any button to exit DEMO mode. NOTE: If the timer or chronograph is running, their values will be displayed in DEMO mode. EN Manual FINAL (RunII) NEW 4/26/99 5:00 PM Page 24 h NIKE ELECTROLITE DISPLAY You can illuminate the display by pressing the Electrolite button. [. . . ]