User manual NIKON LS-30

[. . . ] 35 mm Film Scanner LS-30 User's Guide Cautions · The reproduction of this manual in whole or in part is prohibited save in cases in which Nikon's prior permission has been obtained. The information contained in this manual is subject to change without notice. Nikon has made every effort to produce a perfect manual, but should you find any mistakes, we would be grateful if you would kindly let us know. The address of Nikon's representative in your area is provided separately. [. . . ] If the scanner is plugged into an outlet to which a household appliance such as a vacuum cleaner or air-conditioner is connected, the scanner's power supply may be subject to noise. Unplug the power cable by pulling on the plug, not on the cable itself. Pulling directly on the cord could result in damage that could cause fire or electric shock. The shape of the cable depends on the country of sale · · Do not connect or disconnect the cable while the power is on. Nikon LS-30 35 mm Film Scanner User's Guide 9 3. Setup Step 4--Connect the SCSI cable The LS-30 connects to your computer by a Small Computer Systems Interface, or SCSI. To use a SCSI connection, you will need an appropriate SCSI cable and, in the case of IBM PC/AT compatible computers, a SCSI extension board ("SCSI adapter") or PCMCIA card (see the Fast Track Guide and the LS-30 Reference Manual for details). This section describes the procedure to connecting the LS-30 to a SCSI "chain" made up of your computer and SCSI devices connected to it in a series. SCSI devices cannot be connected while the power is on. Before connecting the scanner to the SCSI chain, be sure that the computer and all other devices in the chain, including the scanner, are off. How the scanner should be connected to the chain depends on whether it is to be located between other devices or attached at the end of the chain. 10 Nikon LS-30 35 mm Film Scanner User's Guide 3. Setup When the scanner is the last device in the chain 1. Set the terminator switch on the rear of the scanner to ON TERMINATOR OFF ON 2. Connect the SCSI cable to either of the two SCSI connectors on the rear of the scanner and connect the other end to the next device in the chain Scanner only external device in chain 100­240V~ 0. 3­0. 2A 50/60 Hz 100098 MADE IN JAPAN SCSI NB 4 5 67 23 TERMINATOR 1 OFF SCSI ON SCSI Other SCSI device Other SCSI device 23 1 SCSI Nikon LS-30 35 mm Film Scanner User's Guide 0 0 Scanner last of several external devices 100­240V~ 0. 3­0. 2A 50/60 Hz 100098 MADE IN JAPAN SCSI NB 4 5 TERMINATOR 67 OFF SCSI ON 11 3. Setup When the scanner is between other devices 1. Set the terminator switch on the rear of the scanner to OFF TERMINATOR OFF ON 2. Connect the SCSI cable from one of the devices in the chain to either of the connectors on the rear of the scanner, then connect a cable to the remaining connector and attach the other end to a connector on the next device in the chain 100­240V~ 0. 3­0. 2A 50/60 Hz 100098 MADE IN JAPAN SCSI NB 4 5 67 23 Other SCSI device TERMINATOR OFF SCSI ON 1 SCSI 3. Confirm that the last device in the chain is terminated Note: If the last device in the chain has an unused SCSI connector, a separate terminator should be attached to it, even if the device is connected to the SCSI chain using a through terminator. 12 Nikon LS-30 35 mm Film Scanner User's Guide 0 Terminator 3. Setup SCSI connection checklist · Turn off the computer, the LS-30, and all SCSI devices before connecting the scanner. · Be sure that the devices at both ends of the SCSI chain are terminated. If the host computer is a Macintosh, the chain will already be terminated at the computer end. In the case of IBM PC/AT compatibles in a chain which contains external devices only, the chain should be terminated at the SCSI board. In the case of a chain which includes internal devices, you may need to remove termination from the board and terminate the last internal device. The maximum number of SCSI devices that can be connected in a single chain is eight, including the computer and any internal SCSI devices such as hard disks or CD-ROM drives. [. . . ] Consult the software reference manual for your platform for more information on the scanner extras available for the LS-30. Step 12--Adjust color balance, contrast, and brightness The controls in the color-balance drawer can be used to adjust RGB color balance, contrast, and brightness. Click the color-balance drawer-tab to open the color-balance drawer. Adjust brightness, contrast, and color balance by dragging the sliders. The effects of these adjustments will be visible in the scan window. 28 Nikon LS-30 35 mm Film Scanner User's Guide 4. [. . . ]