User manual NIKON NIKKOR ED 800MM F/5.6E FL ED VR

[. . . ] English Thank you for your purchase of a NIKKOR lens. Before using this product, please carefully read both these instructions and the camera manual. Note: When mounted on a DX-format digital single-lens reflex camera such as the D7000 or cameras in the D300 series, this lens has an angle of view of 2° and a focal length equivalent to 1200 mm (35 mm format). When the supplied teleconverter is attached, the angle of view is 1°40 and the focal length is equivalent to 1500 mm. [. . . ] OFF may however produce better results in some cases depending on the type of tripod and on shooting conditions. ■ The Lens Hood Type E AF-S lens with built-in CPU and F mount 800 mm f/5. 6 20 elements in 13 groups (including 2 ED lens elements, 2 fluorite elements, and lens elements with Nano-Crystal coatings) and 1 protective glass element Angle of view • Nikon FX-format D-SLR cameras: 3° 10 • Nikon DX-format D-SLR cameras: 2° Distance information Output to camera Focusing Nikon Internal Focusing (IF) System with autofocus controlled by Silent Wave Motor and separate focus ring for manual focus Vibration reduction Lens shift using voice coil motors (VCMs) Focus distance indicator 5. 36 ft) from focal plane Diaphragm blades 9 (rounded diaphragm opening) Diaphragm Automatic electronic aperture control Aperture range f/5. 1 lb) Nikon reserves the right to change the specifications of the hardware described in this manual at any time and without prior notice. 25E ED teleconverter is for use exclusively with AF-S NIKKOR 800 mm f/5. When attached between the camera and the lens, the TC800-1. Autofocus is available only with cameras that offer f/8 support. 2 memory recall/AF start) Focus ring Focus distance indicator Focus distance mark Lens rotation index Slip-in filter holder Slip-in filter holder screw Lens mounting mark Rubber lens-mount gasket CPU contacts Memory set button !9 @0 @1 @2 @3 Strap eyelet Tripod collar ring attachment screw Built-in rotating tripod collar Focus-mode switch Focus limit switch Vibration reduction switch Focus function selector (AF-L/ MEMORY RECALL/AF ON) Beep on/off switch Replaceable monopod collar Lens hood screw Lens hood @4 @5 @6 @7 Teleconverter mounting mark CPU contacts Lens mounting mark Lens release tab ■ Attaching and Removing Lenses Utilisation du commutateur de réduction de vibration • Sélectionnez OFF pour désactiver la réduction de vibration. – Parasoleil Lenses can be attached to and removed from the teleconverter as described below. Attaching Lenses Before removing the lens from the camera for attachment to the teleconverter, find a location out of direct sunlight and turn the camera off. To attach the lens to the teleconverter, align the mounting mark on the lens with the lens mounting mark on the teleconverter and place the lens on the teleconverter lens mount. Being careful not to press the lens release tab, rotate the teleconverter counterclockwise (as seen from the rear) until the lens clicks into place. Removing Lenses Keeping the lens release tab pressed, rotate the teleconverter clockwise (as seen from the rear) until the mounting marks are aligned and then remove the lens from the teleconverter. – Attaching and Removing the Teleconverter q Grip en caoutchouc w Commande de fonction MAP Lens hoods protect the lens and block stray light that would otherwise cause flare or ghosting. E r t y u i o ■ Compatibility This lens can be used with D4, D3-series, D800-series, D700, D600, D300-series, D7100, D7000, D5200, D5100, D5000, D3200, and D3100 cameras. – Focus Fully tighten the hood screw (w). Supported focus modes are shown in the following table (for information on camera focus modes, see the camera manual). Lens focus mode Camera focus mode AF MF A/M Autofocus with manual override (AF priority) M/A Autofocus with manual override (manual priority) M Manual focus with electronic rangefinder The teleconverter can be attached to and removed from the camera as described below. Vignetting may occur if the hood is not correctly attached. The hood can be reversed and mounted on the lens when not in use. [. . . ] A beep will sound if the operation is successful. If the operation fails, the focus distance indicator will revolve back and forth some ten times and the lens will sound a short beep followed by three long beeps; focus and press the memory set button again. € Always support the lens when holding the camera. Failure to observe this precaution could damage the lens mount. [. . . ]