User manual NILES IRP-6-

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual NILES IRP-6-. We hope that this NILES IRP-6- user guide will be useful to you.

Lastmanuals help download the user guide NILES IRP-6-.


Mode d'emploi NILES IRP-6-
Download
Manual abstract: user guide NILES IRP-6-

Detailed instructions for use are in the User's Guide.

[. . . ] B LENDING H IGH F IDELITY AND A RCHITECTURE ® IRP6+ INFRARED EXTENDER SYSTEM-- IR MAIN SYSTEM UNIT Introduction An infrared (IR) extender system enables you to control your IR remote controlled A/V equipment from a remote location. This enables you to place your A/V components out of sight (behind cabinet doors, in the rear of a room, or in a different room) and still conveniently control your equipment. MODEL IRP6+ VID The model IRP6+ is an IR Main System Unit. It is one of three elements that make up an infrared extender system: 1. IR Sensors receive IR commands from hand-held remote controls and relay the commands to the Main System Unit via a 2-conductor shielded cable. [. . . ] 18) Test Flasher Outputs Reconnect one flasher to the second flasher output of the IRP6+. Repeat Step 16 (adjust flasher level and position). · Good Operation: Congratulations!· Poor Operation: Repeat this step with another flasher. · Poor Operation Continues: Go to Step 19 19) Sensors in the Same Room as a Flasher?· If you have sensors in the same room as a flasher: Go to Step 20 · If all sensors are in remote locations without flashers : Go to Step 21 · If you have keypads only: Go to Step 21 20) Optical Feedback Loop If there is an IR sensor and an IR flasher located within the same room an "optical IR feedback loop" can occur. Replace the IRC-1 Flooding Flasher with an IRC-2 MicroFlasher on the front panel sensor window of each component. Place the enclosed IR blocking cover over each of the IRC-2 flashers. · Good Operation: Congratulations!· Poor Operation: Go to Step 16 (adjust Flasher Level and Position) Retest system. · Still Poor Operation: Go to Step 21 21) Replace IRP6+ and Flasher(s) Reconnect the system with a new IRP6+ and new flasher(s). · Poor Operation Continues: Go to Step 22 22) Interference that Does Not Light the IR Test LED Some very rare examples of interference (both optical and electromagnetic) do not light up the IR test LED but do prevent proper operation. Examine your installation carefully for a source of low-level optical or electromagnetic interference. 23) Disconnect All Sensors and Keypads and Test One Sensor Input Disconnect all Sensors and Keypads. Reconnect one of the sensor cables and retest the system (Have someone watch the green IR LED on the IRP6+ while you aim a remote control at a remote sensor and press a button). · IR Test LED Flashes: Go to Step 24 · IR Test LED Off: Go to Step 25 24) Test Second Sensor Input A) If you DO NOT have a second sensor/ Keypad, Go to Step 25. B) If you DO have another sensor/keypad, connect it to the second sensor input. Retest the system Troubleshooting Guide 1) Test Remote Control Verify that the remote control works by operating the equipment directly. If the remote does not operate your system directly, replace the batteries of the remote control. Replace the remote control if necessary. 2) Flasher Positioning Flashers operate line-of-sight; be sure they are unobstructed and aimed at the front panel sensor windows of your components. 3) 12v DC Power Supply Test that the red IRP6+ power LED is on when the wall adapter is plugged into an unswitched AC outlet. [. . . ] Display which source is selected by backlighting the corresponding Source Label. Turn on the local speakers Status LED When the preamp/receiver is on, the status LED is lit. The color of the LED displays whether the local speakers are on or muted. GREEN - Local Speakers and the Preamp/Receiver are on RED - Local speakers are off, but the system is on. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE NILES IRP-6-

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual NILES IRP-6- will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag