User manual NILFISK RS 851

[. . . ] The undersigned certify that the above mentioned model is produced in accordance with the following directives and standards. 00 level RVI RXD VOLVO VDS2 CAT-TO 2 ALLISON C-4 ZF TE ML 04C DEUTZ DQC IV 05 level ISOTTA FRASCHINI Betankungsdaten Kapazität Kraftstofftank Kapazität Öltank Hydraulikanlage Daten elektrische Anlage Anlagenspannung Anlassbatterie Werte 65 Liter (17, 2 USgal) 55 Liter (14, 5 USgal) Werte 12 V 12 V ­ 100 Ah Zulassungen und Spezifikationen CUNA NC 956-16 97 FF. 00 level RVI RXD VOLVO VDS2 CAT-TO 2 ALLISON C-4 ZF TE ML 04C DEUTZ DQC IV 05 level ISOTTA FRASCHINI Données ravitaillements Capacité réservoir carburant Capacité réservoir huile système hydraulique Données système électrique Tension système Batterie de démarrage Valeurs 65 litres (17, 2 US gal) 55 litres (14, 5 US gal) Valeurs 12 V 12 V ­ 100 Ah Approbations et spécifications CUNA NC 956-16 97 FF. This Manual is an integral part of the machine; its purpose is to provide the operator with all necessary information to use the machine properly in a safe and autonomous way. [. . . ] D) together with the safety push-button (16). When necessary, in working mode, shift the 3rd broom to the left or to the right by moving the joystick (15, Fig. Note that, while the skirt is lifted, the machine suction power decreases. If necessary, to collect bulky debris, it is also possible to remove the front skirt (25, Fig. G); remove it according to the following procedure: · Lift the side brooms, then stop the machine and turn off the engine. Turn on the machine and start working again. Install the skirt (3) in the reverse order of removal, after stopping the machine and turning off the engine. After each working cycle, and when the hopper (7, Fig. Dump the hopper according to the following procedure. Turn off the dust control system water pump with the switch (27, Fig. Turn off the suction fan with the lever (8, Fig. If necessary, shift the 3rd broom arm to working mode, by moving the joystick (15, Fig. If the machine must be transferred to an appointed dumping area, engage the parking brake (13, Fig. E), get out of the machine and bring the 3rd broom safety arm from the position (2, Fig. If the hopper may contain a lot of water, it is possible to drain it before lifting and dumping the hopper according to the following procedure: · Close the left upper door (9, Fig. Keep people away from the machine and especially from the hopper (7, Fig. O) and open the rear shoote by turning it from the position (2) to the position (3). Do not move the machine when the hopper is lifted!If machine movement with lifted hopper cannot be prevented, be sure to drive slowest possible speed to avoid lateral instability. If the machine speed exceeds 3 mph (5 km/h) with the hopper lifted, the warning light (3, Fig. D) flashes to warn about the dangerous manoeuvre. D); keep the switch pressed until the door is totally opened. [. . . ] Inside the cab, remove the screw (8, Fig. In winter, perform the following maintenance procedures carefully. Procedures for machine storage or for machines working at less than +32 °F (0 °C) Turn on the water pump (see the procedure in the relevant paragraphs) to let the antifreeze flow through the system until it comes out from the broom nozzles, from the suction hose nozzle and from the rear pipe nozzle (if equipped). When the antifreeze comes out from the nozzles, stop the pump. [. . . ]