User manual NILFISK SMART 2000

[. . . ] American-Lincoln ® Operator's Manual & Parts List SMART 2000 Sweeper/Scrubber Beginning with Serial No. 690119 READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. you must have training in the operation of this machine before using it. [. . . ] To turn the water and solution off turn the knob all the way counterclockwise. NOTE For best results, discontinue application of solution 10 feet before stopping or making a 90° or 180° turn. Figure 14 Figure 13 1 - 18 AMERICAN-LINCOLN TECHNOLOGY SMART 2000 OPERATION OF CONTROLS AND GAUGES - Cont. RECOVERY HIGH LIGHT (See Figure 15) The recovery high warning light will illuminate approximately 5 minutes before the recovery tank is full, giving ample time to complete the scrubbing cycle, before the mechanical float shuts off the vacuum to the recovery tank. LOW SOLUTION LIGHT (See Figure 15) The Low Solution Warning Light is located on the console. The Solution Warning Light will illuminate when the solution tank is empty, marking the end of the scrubbing cycle. Figure 15 B A Figure 16 PARKING BRAKE (See Figure 16) Never leave operator's seat without engaging the parking brake. The parking brake is located on the floor of the machine left of the directional control pedal. To set the parking brake, press down on the foot pedal (Item A) and the press down the lock (Item B). To unlock the parking brake, push down on the upper portion of the foor pedal and release. TURN SIGNAL - 4-Way (Option) The turn signal option is located on the steering column and works as automotive turn signals work, forward on the lever for right and back on the lever for left. The 4-way flasher will activate when the turn signal lever is pulled out. HYDRAULIC RESERVOIR LEVEL SIGHT GAUGE (See Figure 17) The sight gauge is located on the left side of the machine under the front cover. The sight gauge is used to indicate the level of fluid in the reservoir. The fluid level must be visible in the sight gauge when the hopper is in the down position. Figure 17 AMERICAN-LINCOLN TECHNOLOGY SMART 2000 1 - 19 OPERATION OF CONTROLS AND GAUGES - Cont. ACCELERATOR and DIRECTIONAL CONTROL PEDAL - (See Figure 18) The Accelerator and Directional Control Pedal is located on the floor of the operator's area. This pedal controls the machine direction and travel speed. Put foot pressure on the right side of the pedal. Increase the foot pressure on the right side of the pedal to increase the forward speed. Put foot pressure on the left side of the pedal. Increase the foot pressure on the left side of the pedal to increase the reverse speed. To stop the machine, allow directional control pedal to return to neutral (center position). Pedal will automatically return to neutral when foot pedal is released, or put light foot pressure on the opposite end of the accelerator and directional control pedal. If the machine is moving forward, put light foot pressure on the left side of the pedal. If the machine is moving in reverse, put light foot pressure on the right side of the pedal. Figure 18 BACK-UP ALARM SWITCH (Option) The back-up alarm is operated by a switch that is located under the accelerator and directional control pedal mounting plate. The alarm makes a loud audible noise when the machine is being driven in reverse. [. . . ] Nut, Hex Jam, 3/8-24 Flat Washer, 1. 250 x . 280 x . 090 Lock Washer, Int. Carriage Bolt, 1/2-13 x 2. 000 Flat Washer, 1. 13 x . 770 x . 063 Lock Washer, Int. Setscrew, 1/4-20 x . 500 Flat Washer, 1. 000 x . 516 x . 063 Nut, Fiber Insert 5/18-18 Screw, 1/2-13 x 2. 000 HHC Washer, 1. 063 x . 031 x . 063 Screw, 5/16-18 x 1. 750 HHC Screw, 5/16-18 x . 625 HHC Carriage Bolt, 5/16-18 x 2. 250 Washer Screw, M8-1. 250 x . 750 Lock Washer, M14 Split Screw, M14 x 1. 500 x 25 mm HHC Screw, 5/16-18 x 2. 000 HHC Screw, M14 x 35 mm HHC Lock Washer Flat Washer, . 438 x . 200 x . 036 Screw, #8-24 x . 875 OHM Screw, 5/16-24 x 1. 000 HHC Carriage Bolt, 3/8-16 x . 750 Screw, 10-24 x 4. 50 RD. Nut, Hex Jam, . 25-20 Screw, 6-32 x . 50 RHM Screw, 10-24 x . 625 T/C Hex HD. [. . . ]